Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters
40
Reset filters

Settings
Now showing 1 - 10 of 40
  • Publication
    Simulating flow behaviour of wet particles within the immersed tumbling process
    ( 2021)
    Uhlmann, Eckart
    ;
    Polte, Julian
    ;
    Kuche, Yves
    ;
    Landua, Fabian
    For many production chains, it is mandatory to involve special finishing of the manufactured parts for the chipping of the edges as well as the polishing of surfaces. One commonly used method is the immersed tumbling process, where any workpiece is dragged through a particle filled container. In many cases, the immersed tumbling process operates in environments with added liquids, leading to changes in particle-tool interaction and general flow behaviour of the used particles. Whilst the discrete element method for simulating particles is mainly limited to dry particles, the used software ROCKY DEM from ESSS, Florianópolis, Brasil, comes with a built-in liquid-bridge model to simulate water-covered particles and granulate and furthermore an extension for system couplings with Ansys Fluent of the company ANSYS, INC., Canonsburg, Pennsylvania. The latter can be used to create from both software one three-phase-model with higher amounts of actually simulated water. In thi s study, small amounts of water were added to differently shaped particles using the build-in liquid-bridge model, to analyse and compare the particles flow characteristics in both, wet and dry environments. To gather significant information leading towards precise comparisons, the particles trajectories, velocities and resulting forces against the workpieces can be specifically observed and analysed, whilst this kind of process knowledge could previously never been taken into account without simulation.
  • Publication
    Concept for an actuated variable tool electrode for use in sinking EDM
    ( 2021)
    Uhlmann, Eckart
    ;
    Streckenbach, Jan
    ;
    Thißen, Kai
    ;
    Schulte Westhoff, Bela
    ;
    Masoud, Abd Elkarim
    ;
    Maas, Jürgen
    Typically, a large number of individual tool electrodes has to be used in sinking electrical discharge machining (sinking EDM) to successfully machine a single workpiece. Due to non-uniform wear and insufficient flushing of the working gap electrode geometries have a significant effect on the process efficiency. This paper discusses the use of an actuated variable tool electrode for sinking EDM to reduce the number of required tool electrodes and to increase the overall process efficiency. A miniaturised linear actuator was developed to individually move electrode segments to form the target shape for the tool electrode. The coordinated actuation of bundled electrode segments introduces new methods for the active flushing within the working gap, which cannot be implemented in conventional sinking EDM. Intelligent sinking strategies can further improve process efficiency by creating and sinking sub-geometries into the workpiece offering improved flushing conditions compa red to the original geometry.
  • Publication
    Photocatalytic effect of TiO2-coated surfaces on the pathogenic microorganisms E.coli and S.aureus
    ( 2021)
    Uhlmann, Eckart
    ;
    Hein, Christoph
    ;
    Brehmer, Annika
    The use of titanium dioxide as a strong photocatalytic substance can have a large effect in combating the spread of pathogens through heavily contaminated surfaces. For this purpose, various materials, such as metal, glass, and polymer were coated with rutile- and anatase-rich titanium dioxide by sol-gel method. The contact angle and photocatalytic activity of the coated surface were measured under UV irradiation. The anatase-rich titanium dioxide showed higher photocatalytic activity, which further increased with the coating thickness. The process temperature had an effect on the photocatalytic activity due to the temperature-dependent conversion of anatase to rutile crystal conformation. The coated surfaces had strongly reduced contact angles compared to the uncoated material. In particular, the anatase-rich surfaces resulted in superhydrophilic properties. Photocatalytically induced antibacterial activity against pathogenic microorganisms in liquid environments was d emonstrated, especially for gram-negative Escherichia coli bacteria.
  • Publication
    Cutting edge preparation of monolithic ceramic milling tools
    ( 2021)
    Uhlmann, Eckart
    ;
    Polte, Mitchel
    ;
    Polte, Julian
    ;
    Hocke, Toni
    Due to international competition, continuous increases in productivity, product quality and reduction of production costs are required. Especially, the development of milling tools made of innovative cutting materials and application-specific tool geometries for the machining of brittle materials are in focus to overcome these challenges. One approach to improve the performance and the tool behaviour concerning milling of graphite is the use of monolithic ceramic milling tools. Unfortunately, the high brittleness of the ceramic leads to breakouts on the cutting edge during the grinding process. This results in an increased maximum chipping of the cutting edge, which has a significant influence on the milling process. To improve the breakout behaviour, a cutting edge preparation with the immersed tumbling process was applied. To enable a process reliable cutting edge preparation, a suitable lapping medium, the influence of the processing time as well as the depth of imme rsion were investigated. Besides the maximum chipping of the cutting edge, the rounded cutting edge radius was also analysed. The results show that a process reliable cutting edge preparation of monolithic ceramic milling tools with a maximum chipping of the cutting edge RS,max ⤠3 µm and a rounded cutting edge radius of rβ ⤠7 µm could be realised. In future investigations, the experimental applicability of monolithic ceramic milling tools will be proved.
  • Publication
    Effects on part density for a highly productive manufacturing of WC-Co via laser powder bed fusion
    ( 2021)
    Polte, Julian
    ;
    Neuwald, Tobias
    ;
    Gordei, Anzhelika
    ;
    Kersting, Robert
    ;
    Uhlmann, Eckart
    The additive manufacturing of parts made from difficult-to-weld materials through the usage of preheating temperatures of up to Î0 ⤠500 °C is enabled by newest L-PBF machine tools, such as the RenAM 500Q HT from the company RENISHAW PLC, Wottun-under-Edge, UK. This work aims to delevop processing parameters for the dense and crack-free manufacturing of tungsten-carbide cobalt (WC-Co) via this off-the-shelf machine tool. Therefore the laserpower and scanning speed were varied between 80 W ⤠PL ⤠350 W and 140 mm/s ⤠vS ⤠650 mm/s respectively. Furthermore the influence of a continuous and pulsed laser mode was analysed. A focus was set on the identification of parameters that enable a highly productive manufacturing while maintaining a high part density. A parameter set for relative density rel. > 94 % and a buildup rate v = 0.59 mm3/s was developed.
  • Publication
    Improved surface generation of multi-material objects in computed tomography using local histograms
    ( 2021)
    Uhlmann, Eckart
    ;
    Hein, Christoph
    ;
    Kayser, Nicolas
    ;
    Dürre, Gregor
    During the last decade industrial computed tomography (iCT) has become one of the most important metrological procedures for internal inspection, where it sees wide-spread use in injection molding and additive manufacturing. Evaluating the CT volume data of multi-material objects represents a major technical challenge. Due to artifacts caused by beam hardening, an over-segmentation of strongly absorbing materials occurs, severely limiting the accuracy of dimensional measurements. The goal of the project presented is the development of an innovative artifact-reduced multi-material segmentation. This is applied to and tested on various complex reconstructed CT data sets. Global approaches show high signal-to-noise-ratio (SNR) but are not able to compensate for local deviations. For smaller volumes the data sets become more consistent, but the SNR decreases due to the reduced data volume. Thus, a more localized approach for the volume image data has the potential to provid e results of higher accuracy. With this newly presented algorithm it is now possible to perform segmentation of all materials, while eliminating over-segmentation errors as well as local noise artifacts almost completely for all tested datasets.
  • Publication
    Application of tool electrodes oxidised with humid and dry air during the electro-discharge drilling of MAR-M247 alloy
    ( 2021)
    Uhlmann, Eckart
    ;
    Polte, Mitchel
    ;
    Streckenbach, Jan
    ;
    Camin, Bettina
    ;
    Chocholaty, Ondřej
    ;
    Dinh, Ngoc Chuong
    The requirements and challenges of machining advanced materials in the field of aerospace, automotive and tool industry are increasing constantly. Due to their mechanical properties, cutting of high-strength materials such as superalloys is severely limited. Electro-discharge drilling can be used for the manufacturing of holes in hard to machine materials. Although electrical discharge machining (EDM) is successfully applied to the machining of holes in turbine blades, a lack of performance and challenges concerning the geometrical accuracy still remain. By applying inner flushing, the resulting electrically conductive debris is flushed through the lateral working gap, increasing the probability of arcs and short circuits. The resulting increased tool wear, conicity of the hole, limited hole depth and process instabilities are still challenging in electro-discharge drilling. In order to decrease the effects of the arcs and short circuits, a surface modification is appli ed to increase the electrical resistance of the lateral surface of the tool electrode. As a result, the mentioned impairments occur less frequently due to decreased occurrence of arcs and short circuits in the lateral working gap. For the present investigation copper tool electrodes were thermally oxidised in dry and humid air with different durations and used afterwards for electro-discharge drilling of MAR-M247. The tests were carried out on the machine tool AGIETRON Compact 1 from the company GF AgieCharmilles, Losone, Switzerland. Holes with a depth of t = 11 mm were drilled using various surface-modified tool electrodes with a diameter of d = 2 mm. Oxidation with dry air and a extended oxidation time resulted in a 18 % lower erosion duration, accompanied by an increase of the linear wear of the tool electrode Île below 10 %.
  • Publication
    Tool wear and surface roughness in micro-milling of aluminium and high-alloyed aluminium materials using cutting tools made of binderless carbide
    ( 2021)
    Uhlmann, Eckart
    ;
    Polte, Mitchel
    ;
    Wiesner, H.M.
    ;
    Polte, Julian
    ;
    Hein, Christoph
    Micro-milling can be applied for manufacturing in a wide range of materials and complex geometries. This process is especially important for the aerospace industry. High-alloyed aluminium is a common material for aerospace applications with complex micro- and macro-geometry due to its high wear resistance. The costs-effectiveness of producing these parts can be increased by using tools with improved wear behaviour and higher life times. However, wear-resistant tools are often associated with higher tool costs, which reduces the cost-effectivness of the whole production. An innovative solution is offered by the use of a cutting tool made of binderless tungsten carbide. The micro-milling of conventional and high-alloy aluminium with a new cutting material based on a binderless tungsten carbide is analysed in this investigation. The absence of a binding phase leads to an increased hardness and improves the wear behaviour of these tools. Therefore, tools with a tool diamete r of D = 10 mm were manufactured and there machinability was successfully proven. The feasibility of these innovative tools is demonstrated in a series of experiments. The experimental investigations were carried out on the five-axis high precision machine tool PFM 4024-5D PRIMACON GMBH, Peißenberg, Germany, with a workpiece made of TiAl 48-2-2. A surface roughness of Ra = 0.202 µm was detected after a path length due to primary motion lc = 70 m without any noticeable wear marks on the cutting tool. These results show the economic potential for milling tools based on binderless carbide for achieving high precision surfaces while reaching high lifetimes.
  • Publication
    Micro-milling of a sprue structure in tungsten carbide-based metal matrix composite
    ( 2021)
    Uhlmann, Eckart
    ;
    Polte, Julian
    ;
    Polte, Mitchel
    ;
    Hein, Christoph
    ;
    Hocke, Toni
    ;
    Jahnke, Christian
    Many industries rely on plastic components manufactured by micro-injection moulding. There is a high potential to further increase the cost-effectiveness by machining the moulds needed for this process from non-ferrous metals and reinforcing the parts of the mould, which experience high loads during the micro-injection moulding. Inserting tungsten carbide particles locally into the surface of these non-ferrous metals is one possibility of reinforcement. The resulting metal-matrix-composites (MMC) exhibit the needed wear resistance, while the ground material can be machined very effectively through micro-milling. In contrast, the Micro-milling of these MMC-materials is challenging and so far not state of the art. Thus, this investigation is concerned with the development and qualification of micro-milling parameters for tungsten carbide-based MMC-materials. Binderless polycrystalline diamond as innovative cutting material was applied for this purpose. The goal of the mil ling parameter development was to optimize the surface roughness and the form accuracy for machining an aluminium bronze workpiece reinforced with tungsten carbide particles through laser injection. Based on an analysis of a wide range of process parameters, an optimised milling strategy was applied to machine a sprue structure from the described MMC-material. Different parameter sets are evaluated by analysing the form accuracy and measuring the surface roughness of machined structures. A surface roughness of Ra = 80 nm and form accuracy of a = 3 µm could be achieved with optimized micro-milling parameters and qualified the developed parameters for industrial applications.
  • Publication
    Precision finishing of additively manufactured components using the immersed tumbling process
    ( 2021)
    Polte, Julian
    ;
    Polte, Mitchel
    ;
    Hocke, Toni
    ;
    Lahoda, Christian
    ;
    Uhlmann, Eckart
    Additive manufacturing enables the production of highly complex metallic components with highest geometrical flexibility in dedicated lightweight construction. For titanium-aluminium alloys, which are used in particular in the aviation industry, powder bed based processes such as the laser powder bed fusion are established. Nevertheless, laser powder bed fusion is limited with regard to the producible surface roughness in a range of 5 µm ⤠Ra ⤠15 µm. According to the state of the art, the increase of the geometrical accuracy and the reduction of the surface roughness values of the additive manufactured components are realised by different cutting and non-conventional processes. In this investigation, a new approach for the reduction of the surface roughness values by immersed tumbling was realised. Therefore, additively manufactured square bars made of the titanium alloy Ti-5Al-5Mo-5V-3Cr were used as sample geometries. An immersed tumbling machine tool with plan etary kinematics for post-processing was applied and the lapping media QZ, HSC 1/500 and M5/400 were evaluated. In addition, the influence of the rotor speed and the holder as well as the depth of immersion were considered as influencing factors. As target values the surface roughness values as well as the rounded edge radius were examined. Within this investigations the surface roughness values could be reduced by more than 90 %. In addition, a targeted rounding of the edges could be obtained, which removed the excess edge height at the part resulting from the laser powder bed fusion process. As a result the immersed tumbling process shows a great suitability as a finishing process for additively manufactured components and is particularly suitable for automated and serial finishing processes.