1 - 4 of 4
-
PublicationProcess stabilization through pulsed laser-induced melt pool shaping in dual-beam LMD( 2022)Laser Metal Deposition (LMD) is an additive manufacturing process that reaches high deposition rates. Its applications are mainly found in repair, cladding and manufacturing. The two commonly used LMD processes are powder-based (LMD-p) and wire-based (LMD-w). Despite the fact that wire-based LMD uses material more efficiently, its process stability is a major concern. One approach to increase the process stability is superposing a pulsed laser (pw) beam with the conventionally used continuous laser (cw). Previous studies have shown that the metal vapor caused by pulsed laser-induced evaporation in the process zone significantly improves energy absorption. Furthermore, a direct relation between vapor pressure and melt pool form has been demonstrated. In this contribution, we correlate the pw-controlled melt pool geometry to process stability. High-speed camera imaging is employed to evaluate the dynamic melt pool behavior as a function of pw frequency and power. It is shown that irregular melt pool oscillations impairing process stability in conventional LMD-w are reduced if the pulsed laser is added. The melt front is shaped depending on the acting pw-induced pressure. This leads to a more stable interaction between wire and melt pool. Furthermore, the pw pressure changes the welding bead height and width. This cross-sectional geometry has an impact on the resulting waviness in 3D build-up. We also investigate how the waviness influences process stability during multilayer LMD-w. The results demonstrate that the dual beam technology is a promising way to develop more reliable and resource-efficient AM processes.
-
PublicationExpress Wire Coil Cladding (EW2C) as an Advanced Technology to Accelerate Additive Manufacturing and Coating( 2021)Metal shafts are indispensable components in mobility, energy and mechanical engineering. In such applications, the shafts need to withstand severe mechanical loads, friction, high temperature or corrosive media. This is why shafts are often completely made of high-performance alloys. From a technical point of view, coating an inexpensive base shaft with a thin layer of high-performance material is mostly sufficient to ensure its functionality. Adding functional parts such as shoulders or bearing seats by Additive Manufacturing (AM) instead of creating them by subtractive manufacturing is an advantageous approach to increase flexibility and material efficiency. Reliable and economic AM and coating processes need to be developed further, and laser-based processes such as wire-based Laser Metal Deposition (LMD-w) offer high potential to accomplish this. They can generate a stable metallurgical bond between the base material and the cladding or the added feature without excessively heating the work piece. Due to their low build-up rate, however, LMD processes are not economically competitive with high-speed subtractive technologies such as drilling or turning, which are predominately used for shaft production. Motivated by this challenge, we present an alternative approach that increases the deposition rate for laser-based shaft cladding. Instead of adding the filler wire continuously, wire coils are wound and preplaced on the shaft. In a second step, laser processing while rotating the part generates a metallurgical bond between the wire and the substrate. In this study, several solid and flux-cored wires were analyzed regarding their suitability for this two-step coil winding and LMD process. The results from LMD experiments give an overview of the resulting surface state and of the welded joint quality after deposition. Metallographic cross sections show low porosity of the deposited layers and small heat-affected zones in the base shaft. Thanks to its good scalability, this innovative two-step process can help strongly increase the build-up rate compared to classic LMD-w.
-
PublicationReflectometry-based investigation of temperature fields during dual-beam Laser Metal Deposition( 2021)Laser Metal Deposition (LMD) is a high deposition rate metal Additive Manufacturing process. Its applications are basically repair, cladding and manufacturing. The two most commonly used LMD processes are powder-based (LMD-p) and wire-based (LMD-w). Despite the fact that wire-based LMD is more material efficient, process stability is a major concern. By adding a modulated laser beam to the continuous process beam, a change of the melt pool geometry and increased energy absorption are observed. This relation shows great potential to increase process stability. In this contribution, the positive effect of the dual laser-beam use on LMD-w processes is demonstrated. To understand the cause-effect relation, the workpiece temperature field was investigated by optical backscatter reflectometry ( OBR). The results were then correlated to simultaneously performed IR camera measurements of the workpieces upper surface. By better understanding the thermal phenomena in dual-beam LMD, research can improve process temperature control. This leads to a new perspective for the LMD-w manufacturing process in many industry sectors such as mobility, energy and engineering.
-
PublicationRessourcenschonende additive Fertigung. Herstellung und Reparatur von Hochleistungsantriebswellen( 2021)
