Dr.

Günther, Daniel

Filters

6 2
Reset filters

Settings
Now showing 1 - 8 of 8
  • Publication
    On the mechanism of binder migration in furan binder jetting of sand molds and cores
    ( 2024-03-05)
    Hartmann, Christoph
    ;
    Silberhorn, Jonas
    ;
    Erhard, Patricia
    ;
    Günther, Daniel
    Binder Jetting is a layer-based additive manufacturing process in which a printhead deposits droplets onto a preprepared layer of particles. Upon droplet impact, the binder begins to migrate and infiltrate adjacent areas away from its originally intended location. The purpose of this study is to investigate the mechanism of furan binder migration. Observing in-situ binder spreading is challenging, especially for the furan binder used in this work. The strong discoloration of the surrounding sand makes it difficult to distinguish between the printed pattern and the surrounding loose sand. For this reason, a fluorescent dye is added to the binder. A wavelength-matched laser in the binder jetting machine provides the excitation energy, and in-situ observation of binder migration becomes feasible. The results show an unexpected behavior where the actual microscopic fluid redistribution of the binder does not match the observed macroscopic measurements of other reports. It becomes clear that the migration mechanism of furan binder in sand binder jetting is strongly influenced by gaseous mass transport. To support this theory, a phenomenon called boundary zone is studied by micrographic and computed tomographic analysis. This outer shell region surrounds samples with higher binder contents and extends over a thickness of approximately 400 µm. The binder content here is significantly higher than that of the core of the specimen and its target value, demonstrating that liquid concentration equalization is not feasible. A plausible explanation is evaporation and condensation of binder, resulting in localized binder accumulation in areas of high catalyst to binder ratios. Since binder evaporation is an overlooked issue in furan binder jetting, additional experiments are performed to demonstrate the extent of evaporation. For this, particle layers are deposited on a scale, the printhead deposits binder, and the resulting mass loss is recorded. With a better understanding of binder migration, new strategies can be developed to reduce geometric deviation, improve geometric precision, and possibly allow for higher layer thicknesses in furan sand binder jetting.
  • Publication
    Sintering of 3D-printed aluminum specimens from the slurry-based binder jetting process
    ( 2024)
    Angenoorth, Jan Maximilian Golo
    ;
    Erhard, Patricia
    ;
    Wächter, Dennis
    ;
    Volk, Wolfram
    ;
    Günther, Daniel
    This work investigates a novel method of producing complex-shaped aluminum parts by slurry-based binder jetting and sintering. In this process, a green body is built up by layer-wise deposition of an aqueous aluminum suspension and selective powder bonding by ink-jet printing. The powder bulk generated from the suspension shows an increased density compared to powder-based binder jetting and, thus, a high initial density for the subsequent densification step. This allows for higher final densities and reduced shrinkage. Aluminum is of special interest as it is widely available and of low density but challenging to sinter due to an oxide skin surrounding every particle. The research in this paper investigates the effects of the sintering atmosphere and sintering additives on the microstructure of powder compacts produced by slurry-based binder jetting. The incorporation of magnesium as an additive during the sintering process of aluminum has been found to substantially improve densification during sintering in an argon atmosphere.
  • Publication
    Advanced Procedures for Series Production with 3D-Printed Core Packages
    ( 2023)
    Erhard, Patricia
    ;
    Hartmann, Christoph
    ;
    Li, Rui
    ;
    Volk, Wolfram
    ;
    Günther, Daniel
    The application of additive-manufactured cores and molds is of great interest for complex cast components. Nevertheless, several challenges still exist in utilizing binder jetting in the multi-step additive manufacturing process for foundry applications to its fullest extent. This contribution shows methods that facilitate the use of 3D-printed sand molds and cores in casting series applications. The binder jetting process itself is assessed from an overall process chain perspective to highlight the benefits of its application in series production. The challenges associated with automating mold cleaning for highly complex casting contours are depicted. In particular, employing the method of cleanable mold partitioning is shown to enhance the automation level of the overall process. Mold design tailored to 3D printing is demonstrated to contribute to overall cost and time savings in enhanced core packages. Topology-optimized, lightweight part designs involving complex freeform surfaces may require mold partitioning associated with laborious burr removal processes. A new approach in answer to the shortage of skilled workers in the harsh and hazardous foundry environment is shown. Implementing motion tracking technology is demonstrated to enable economical automated burr removal for minor quantities or high variant diversity in the future foundry. All the methods shown are of great importance for introducing printed core packages into series production.
  • Publication
    Influence of the Resin System and Sand Type on the Infiltration of 3D-Printed Sand Tools
    ( 2023)
    Erhard, Patricia
    ;
    Taha, Iman
    ;
    Günther, Daniel
    Binder jetting is a highly productive additive manufacturing (AM) method for porous parts. Due to its cost-effectiveness, it is used for large components and quantities ranging from prototyping to series production. Post-processing steps like sintering or infiltration are common in several applications to achieve high density and strength. This work investigates how 3D-printed sand molds can be infiltrated with epoxy resins without vacuum assistance to produce high-strength molds for thermoforming applications. Specimens 3D-printed from different sand types are infiltrated with resins of different viscosity and analyzed for infiltration velocity and depth. The infiltration velocities corresponded well with the correlation described in Washburn’s equation: The resins’ viscosities and the saturation level were decisive. Amongst the investigated sand types commonly used in foundries, sand type GS19 was found most suitable for infiltration. However, the sand type proved to be a less relevant influencing factor than the resins’ viscosities and quantities applied. Infiltration of topology-optimized 3D-printed sand tools up to a wall thickness of 20 mm for thermoforming applications was found to be feasible.
  • Publication
    Simulation of Binder Infiltration in Additive Manufacturing of Sand Molds
    ( 2023)
    Erhard, Patricia
    ;
    Tanjavooru, Vivek Teja
    ;
    Hartmann, Christoph
    ;
    Bosch, Lucas Valentin van den
    ;
    Seidel, Alexander
    ;
    Volk, Wolfram
    ;
    Günther, Daniel
    This article proposes a computational fluid dynamics approach to simulate binder infiltration in 3D printing of sand molds using OpenFOAM facilitating the identification of suitable levers for application-specific material and process developments. A method for randomly generating powder bulks of designated powder size distributions (PSD) and procedures for automated analysis of the infiltration profile and volume are introduced. Simulation is utilized to investigate binder infiltration using different droplet spacings, representing different printheads’ resolutions. The apparent particle size at the exact location of the droplets’ impact, the droplets’ landing position in relation to the respective surface topography, and thus the statistical appearance of particle formations appear to be influencing the infiltration profile. High-speed camera observations show the plausibility of the predicted infiltration kinetics. An exemplary use case compares the predicted infiltration profiles to the compressive strength of specimens printed from silica sand with low binder contents. Simulation predicts an average infiltration of 250 μm that presumably achieves reliable bonding for layer thicknesses up to 365 μm. A decrease in strength with increasing layer thickness at constant binder contents can be found in the experiment – at layer thicknesses above 350 μm, only minor strengths are achieved.
  • Publication
    Innovative Salzkerne für komplexe Geometrien
    ( 2022-08)
    Erhard, Patricia
    ;
    Günther, Daniel
    Das Fraunhofer IGCV und die K+S Aktiengesellschaft haben in einem gemeinsamen F&E-Projekt eine übergreifende nachhaltige Prozesskette für das Schießen von Salzkernen zur Darstellung innen liegender Kavitäten im Aluminiumguss entwickelt. Im Vergleich zu konventionellen Sandkernen nutzt das vorgestellte alternative Verfahren ein Salzgemisch zur Herstellung binderfreier Salzkerne, welches mit Wasser rückstandsfrei ausgespült werden kann. Die dabei entstehende wertstoffhaltige Salzlösung kann, so das erarbeitete Konzept, von der K+S Aktiengesellschaft recycelt werden. Die neue Technologie überzeugt durch hohe Geometriefreiheit und besonders durch die erleichterte Entkernbarkeit der Bauteile.
  • Publication
    Characterization of Slurry-Cast Layer Compounds for 3D Printing of High Strength Casting Cores
    ( 2021)
    Erhard, Patricia
    ;
    Angenoorth, Jan
    ;
    Vogt, Joachim
    ;
    Spiegel, Johannes
    ;
    Ettemeyer, Florian
    ;
    Volk, Wolfram
    ;
    Günther, Daniel
    Additive manufacturing of casting cores and molds is state of the art in industrial application today. However, improving the properties of chemically bonded casting cores regarding temperature stability, bending strength, and surface quality is still a major challenge. The process of slurry-based 3D printing allows the fabrication of dense structures and therefore sinterable casting cores. This paper presents a study of the slurry-based fabrication of ceramic layer compounds focusing on the drying process and the achievable properties in slurry-based 3D printing of casting cores. This study aims at contributing to a better understanding of the interrelations between the drying conditions in the 3D printing process and the properties of sintered specimens relating thereto. The drying intensity influenced by an IR heater as well as the drying periods are varied for layer thicknesses of 50, 75, and 100 µm. Within this study, a process window applicable for 3D printing of sinterable casting cores is identified and further indications are given for optimization potentials. At layer heights of 75 µm, bending strengths between ~8 and 11 MPa as well as densities of around 50% of the theoretical density were achieved. Since the mean roughness depth Rz is determined to be <30 µm in plane, an application of slurry-based 3D printing in investment casting is conceivable.
  • Publication
    3D Printed Sand Tools for Thermoforming Applications of Carbon Fiber Reinforced Composites - A Perspective
    ( 2021)
    Günther, Daniel
    ;
    Erhard, Patricia
    ;
    Schwab, Simon
    ;
    Taha, Iman
    Tooling, especially for prototyping or small series, may prove to be very costly. Further, prototyping of fiber reinforced thermoplastic shell structures may rely on time-consuming manual efforts. This perspective paper discusses the idea of fabricating tools at reduced time and cost compared to conventional machining-based methods. The targeted tools are manufactured out of sand using the Binder Jetting process. These molds should fulfill the demands regarding flexural and compressive behavior while allowing for vacuum thermoforming of fiber reinforced thermoplastic sheets. The paper discusses the requirements and the challenges and presents a perspective study addressing this innovative idea. The authors present the idea for discussion in the additive manufacturing and FRP producing communities.