Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters

8
8
Reset filters

Settings
Now showing 1 - 8 of 8
  • Publication
    Framework of an experimental setup to enable an adaptive process control based on surrogate modelling
    ( 2022)
    Uhlmann, Eckart
    ;
    Polte, Julian
    ;
    Bösing, Manuel
    ;
    Schuler, Niklas
    Numerical simulations can help to reduce the necessity of experimental studies. Nevertheless, these simulations are costly in terms of their computational effort resulting in significant expenditure of time and hence prevent a flexible adaption to continuously changing process conditions in real time. To address this shortcoming, the paper describes a framework for the application of surrogate models to enable an adaptive process control in real time. Following, an experimental setup to validate the general framework is designed for a laser metal deposition process. In particular, the component distortion shall be simulated and the results are then used to train the surrogate models. By measuring the final component distortion the quality of the surrogate models can be assessed.
  • Publication
    Residual stresses in additive manufactured precision cemented carbide parts
    ( 2022)
    Polte, Julian
    ;
    Polte, Mitchel
    ;
    Hocke, T.
    ;
    Blankenburg, Malte
    ;
    Lahoda, Christian
    ;
    Uhlmann, Eckart
    Due to the good strength properties and high hardness, components made of cemented carbide are used in various industrial sectors as key components, e.g. mould making and matrices. Precision cemented carbide parts are mainly machined by milling and electrical discharge machining (EDM). Nevertheless, long machining times and excessive tool wear are remaining challenges at the state of the art. A promising approach to overcome these challenges is the machining of precise cemented carbide parts using a process chain consisting of near-net-shape laser powder bed fusion (LPBF) and subsequent finishing using a dedicate diamond slide burnishing process. Within previous investigations a geometrical accuracy of ag ≤ 10 µm and a reduction of the surface roughness by Ra = 89 % could be achieved. Within this work plastic deformation induced by the diamond slide burnishing and the effects on the material properties in the surface area were investigated, e.g. residual stresses. For this purpose, the lattice distortion of the metallic cobalt phase was measured by X-ray diffraction using high-energy synchrotron radiation. In addition, the height profile of the residual stresses was also recorded in distances of d = 3 µm to obtain information about the depth effect of the diamond slide burnishing process. Based on the investigations an increase of the residual compressive stresses could be obtained. This shows a particularly positive effect especially for additively manufactured components, as these often show a slight porosity and higher surface roughness as conventional manufactured components. In this way, crack propagation can be prevented and the fatigue strength can be increased.
  • Publication
    Additive manufacturing of precision cemented carbide parts
    ( 2021)
    Polte, Julian
    ;
    Polte, Mitchel
    ;
    Lahoda, Christian
    ;
    Hocke, Toni
    ;
    Uhlmann, Eckart
    Cemented carbide parts are commonly used as wear resistance components in a broad range of industry, e.g. for forming, mould making and matrices. At state of the art the machining of precision cemented carbide components by milling is strongly limited due to excessive tool wear and long machining times. Promising approaches for precision machining of cemented carbide components are dedicated cutting tool coatings, new cutting materials like binderless polycrystalline diamond and ultrasonic-assisted machining. Nevertheless, for all these approaches the components need to be machined of monolithic materials. The new approach addresses an innovative manufacturing process chain composed of near net shape Additive Manufacturing followed by a precision finishing process. Within this investigations for the manufacturing of precision cemented carbide parts, cemented carbide with a cobalt content of 17 % and a grain size in a range of 23 µm ⤠gs ⤠40 µm were used. As Addit ive Manufacturing technology laser powder bed fusion was used. Diamond slide burnishing and immersed tumbling were investigated as finishing technologies. Based on the investigations, a dedicated process chain for the manufacturing of precision cemented carbide parts could be realised. The findings show that the developed process chain composed of near net shape Additive Manufacturing and the finishing process diamond slide burnishing enables the manufacturing of precision cemented carbide parts with a geometrical accuracy of ag ⤠10 µm. Due to the finishing process the initial surface roughness after Additive Manufacturing could reduce by Ra = 89 %.
  • Publication
    Effects on part density for a highly productive manufacturing of WC-Co via laser powder bed fusion
    ( 2021)
    Polte, Julian
    ;
    Neuwald, Tobias
    ;
    Gordei, Anzhelika
    ;
    Kersting, Robert
    ;
    Uhlmann, Eckart
    The additive manufacturing of parts made from difficult-to-weld materials through the usage of preheating temperatures of up to Î0 ⤠500 °C is enabled by newest L-PBF machine tools, such as the RenAM 500Q HT from the company RENISHAW PLC, Wottun-under-Edge, UK. This work aims to delevop processing parameters for the dense and crack-free manufacturing of tungsten-carbide cobalt (WC-Co) via this off-the-shelf machine tool. Therefore the laserpower and scanning speed were varied between 80 W ⤠PL ⤠350 W and 140 mm/s ⤠vS ⤠650 mm/s respectively. Furthermore the influence of a continuous and pulsed laser mode was analysed. A focus was set on the identification of parameters that enable a highly productive manufacturing while maintaining a high part density. A parameter set for relative density rel. > 94 % and a buildup rate v = 0.59 mm3/s was developed.
  • Publication
    Application of additive manufactured tungsten carbide-cobalt electrodes with interior flushing channels in S-EDM
    ( 2020)
    Uhlmann, Eckart
    ;
    Polte, Julian
    ;
    Bolz, Robert
    ;
    Yabroudi, Sami
    ;
    Streckenbach, Jan
    ;
    Bergmann, André
    Application fields of electrical discharge machining (EDM) are limited due to given process conditions. Manufacturing of parts with high aspect ratios and the application of multi-axis machining are limited due to process instabilities caused by removed particles. A promising approach to improve EDM process conditions, especially in sinking EDM (S-EDM), is the utilization of flushing channels in the tool electrode. However, with increasing complexity of the tool electrode geometry and the local integration of these flushing channels, conventional tool electrode manufacturing by cutting is limited. In contrast to that, the machining process selective laser melting (SLM) does not have such limitations. The appropriate integration of flushing channels, even for complex electrode geometries, improves process conditions during EDM in a variety of applications. This leads to a higher material removal rate and reduced tool wear compared to machining without flushing. Additionally, the number of required tool electrodes can be reduced, as SLM enables an efficient integration and miniaturization of all features in a single electrode. Because of its wear resistance and stability, tungsten carbide is an ideal tool electrode material, which is commonly applied in drilling EDM. After identifying suitable process parameters for roughing EDM with additively manufactured tungsten carbide cobalt tool electrodes, different forms of flushing channels were analysed in order to establish a fast process with minimum tool electrode wear. The results concerning material removal rate and the relative tool wear could be improved by applying internal flushing, though the tool wear stayed at a worse level compared to conventional tool electrode materials.
  • Publication
    Heat treatment of SLM-LMD hybrid components
    ( 2019)
    Uhlmann, Eckart
    ;
    Düchting, Jan
    ;
    Petrat, Torsten
    ;
    Graf, Benjamin
    ;
    Rethmeier, Michael
    Additive manufacturing is no longer just used for the production of prototypes but already found its way into the industrial production. However, the fabrication of massive metallic parts with high geometrical complexity is still too time-consuming to be economically viable. The combination of the powder bed-based selective laser melting process (SLM), known for its geometrical freedom and accuracy, and the nozzle-based laser metal deposition process (LMD), known for its high build-up rates, has great potential to reduce the process duration. For the industrial application of the SLM-LMD hybrid process chain it is necessary to investigate the interaction of the processes and its effect on the material properties to guarantee part quality and prevent component failure. Therefore, hybrid components are manufactured and examined before and after the heat treatment regarding the microstructure and the hardness in the SLM-LMD transition zone. The experiments are conducted using the nickel-based alloy Inconel 718.
  • Publication
    Application of additive manufactured tungsten carbide tool electrodes in EDM
    ( 2018)
    Uhlmann, Eckart
    ;
    Bergmann, André
    ;
    Bolz, Robert
    ;
    Gridin, Witalij
    Application fields of electrical discharge machining (EDM) are limited due to given process conditions. When producing structures of high aspect ratios or using multi-axis machining, removed particles assemble at the machining zone, leading to process instabilities. A promising approach to improve EDM process conditions is the utilization of flushing channels in the tool electrode. However, with increasing complexity of the electrode geometry and the local integration of the mentioned flushing channels, conventional electrode manufacturing reaches its limitations. By applying Selective Laser Melting (SLM), these limitations are eliminated. The appropriate integration of flushing channels, even for complicated electrode geometries, improves process conditions during EDM in a variety of applications, leading to a higher material removal rate VW and reduced tool wear TH compared to machining without flushing. Additionally, the number of required tool electrodes can be reduced, as SLM enables an efficient integration and miniaturization of all features in a single electrode. Of particular interest in the field of EDM is carbide. Because of its wear resistance and stability, it is an ideal electrode material, which is commonly applied in mEDM. Tungsten carbide-cobalt is representative for this group of materials, which is already used in tool manufacturing. Several tests show a general suitability of carbide tool electrodes made by SLM for EDM-processing. However, the SLM process parameters and the composition of the carbide-cobalt show significant impact to the EDM results. A lower proportion of cobalt leads to reduced material removal rates VW and rising tool wear.
  • Publication
    Manufacturing of carbide tools by Selective Laser Melting
    ( 2018)
    Uhlmann, Eckart
    ;
    Bergmann, André
    ;
    Bolz, Robert
    Application fields of electrical discharge machining (EDM) are limited due to given process conditions. When producing structures of high aspect ratios or using multi-axis machining, removed particles assemble at the machining zone, leading to process instabilities and increasing tool wear. A promising approach to improve EDM process conditions is the utilization of flushing channels in the tool electrode. However, with increasing complexity of the electrode geometry and the local integration of the mentioned flushing channels, conventional electrode manufacturing reaches its limitations. By applying Selective Laser Melting (SLM), these limitations are eliminated. An additional benefit is the efficient use of material during SLM, where nearly no waste is produced, because remaining powder can be used for the next SLM-process. The appropriate integration of flushing channels, even for complicated electrode geometries, improves process conditions during EDM in a variety of applications, leading to a higher material removal rate VW and reduced tool wear TH compared to machining without flushing. Additionally, the number of required tool electrodes can be reduced, as SLM enables an efficient integration and miniaturization of all features in a single electrode, what results in a far more sustainable process chain. Of particular interest in the field of EDM is carbide. Because of its wear resistance and stability, it is an ideal electrode material, which is commonly applied in µEDM. Tungsten carbide-cobalt is representative for this group of materials, which is already used in tool manufacturing. Several tests show a general suitability of carbide tool electrodes made by SLM for EDM-processing. However, the SLM process parameters and the composition of the carbide-cobalt show significant impact to the EDM results. A lower proportion of cobalt leads to reduced material removal rates, whereas the level of tool wear remains at a similar level. In order to benefit from the advantages of additive manufactured carbide tool electrodes, this investigation aims at decreasing waste of material and the number of required tool electrodes.