Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters

6
Reset filters

Settings
Now showing 1 - 6 of 6
  • Publication
    Validation of different tungsten carbide-cobalt grades as tool electrode material for sinking EDM
    ( 2022)
    Uhlmann, Eckart
    ;
    Bolz, Robert
    ;
    Polte, Mitchel
    ;
    Börnstein, Julian
    In sinking electrical discharge machining (EDM), tool electrode wear is crucial for an economical production. The tool electrode wear affects the process efficiency and determines the number of required tool electrodes for a specific machining process. Therefore, the relative tool wear, describing the relation of removed material volume between tool and workpiece electrode, needs to be minimised. The tool wear characteristics in sinking EDM depend strongly on EDM processing parameters and the applied electrode materials. Especially in micro-EDM, a significant increase of relative tool wear is representative. Because of its thermophysical properties tungsten carbide-cobalt (WC-Co) is a suitable material for the application as sinking EDM tool electrode. The economical production of WC-Co form electrodes for EDM sinking is enabled by recent advancements in precision milling of hard materials. Due to non-existent research on which composition of WC-Co is most advantageous for the application as sinking EDM tool electrode material, previous investigations have been intensified to describe correlations between material properties, EDM processing parameters and EDM processing results concerning material removal rate and relative tool wear. Therefore, various WC-Co grades with differing grain size and cobalt content were analysed in sinking EDM experimental studies. It was observed that the factor grain size showed an ambiguous effect concerning the process results. An increasing cobalt content led to a reduction of relative tool wear, which can be explained by the microstructure of the cobalt binder phase with its higher electrical conductivity. The WC-Co grades with beneficial EDM processing results have been further investigated in EDM parameter studies with differing tool electrode geometries. The experimental results concerning relative tool wear, with a minimum of 3 % for macro- and 5 % for micro-sized geometries, proved the suitability of specific WC-Co compositions as tool electrode material for sinking EDM.
  • Publication
    Application of additive manufactured tungsten carbide-cobalt electrodes with interior flushing channels in S-EDM
    ( 2020)
    Uhlmann, Eckart
    ;
    Polte, Julian
    ;
    Bolz, Robert
    ;
    Yabroudi, Sami
    ;
    Streckenbach, Jan
    ;
    Bergmann, André
    Application fields of electrical discharge machining (EDM) are limited due to given process conditions. Manufacturing of parts with high aspect ratios and the application of multi-axis machining are limited due to process instabilities caused by removed particles. A promising approach to improve EDM process conditions, especially in sinking EDM (S-EDM), is the utilization of flushing channels in the tool electrode. However, with increasing complexity of the tool electrode geometry and the local integration of these flushing channels, conventional tool electrode manufacturing by cutting is limited. In contrast to that, the machining process selective laser melting (SLM) does not have such limitations. The appropriate integration of flushing channels, even for complex electrode geometries, improves process conditions during EDM in a variety of applications. This leads to a higher material removal rate and reduced tool wear compared to machining without flushing. Additionally, the number of required tool electrodes can be reduced, as SLM enables an efficient integration and miniaturization of all features in a single electrode. Because of its wear resistance and stability, tungsten carbide is an ideal tool electrode material, which is commonly applied in drilling EDM. After identifying suitable process parameters for roughing EDM with additively manufactured tungsten carbide cobalt tool electrodes, different forms of flushing channels were analysed in order to establish a fast process with minimum tool electrode wear. The results concerning material removal rate and the relative tool wear could be improved by applying internal flushing, though the tool wear stayed at a worse level compared to conventional tool electrode materials.
  • Publication
    Dry-ED milling of micro-scale contours with high-speed rotating tungsten tube electrodes
    ( 2020)
    Uhlmann, Eckart
    ;
    Perfilov, I.
    ;
    Yabroudi, Sami
    ;
    Mevert, Ricardo
    ;
    Polte, Mitchel
    This paper presents machining results for dry-ED milling of micro-scale contours by use of a new machine tool, including a relaxation generator, designed for dry-EDM. To implement the dry-ED milling process tungsten tube electrodes were used. The gas is injected through the tubular tool electrode under high pressure. Additionally, a high-speed EDM spindle was used to overcome process instabilities and increase the material removal rate due to better flushing conditions. Further, fluid simulations of the flushing conditions are presented in this paper. It is found that the use of gaseous dielectrics enables much better machining results in terms of shape accuracy and tool wear. The simulations provide new insights in the flushing conditions when using gaseous dielectrics. The calculated fluid flow pattern shows a great agreement with the observed depositions of reattached molten material on the tool and workpiece surface. The results presented as well as the hardware introduced enable the industrial application of dry-EDM for the first time.
  • Publication
    Fundamental research of applying tungsten carbide-cobalt as tool electrode material for sinking EDM
    ( 2020)
    Uhlmann, Eckart
    ;
    Polte, Mitchel
    ;
    Bolz, Robert
    ;
    Börnstein, Julian
    The manufacturing process milling is limited in machining specific geometries like inner contours with sharp edges, high aspect ratios or defined radii. Sinking EDM (S-EDM) is an appropriate process to machine complex features if the negative geometry is machinable. The tool electrode wear is a critical factor, because it affects machining accuracy and process efficiency. The tool electrode wear depends on S-EDM processing parameters, the geometry and material of the tool electrode. The material tungsten carbide-cobalt owns suitable thermophysical properties for the application as tool electrode material in EDM. Most applications of tungsten carbide-cobalt in EDM are limited to EDM drilling processes, where tungsten carbide tube electrodes are widely used. The advancements in milling of hard materials enable an economic manufacturing of tungsten carbide-cobalt form electrodes for sinking EDM applications. However, it is not investigated which composition of the material tungsten carbide-cobalt is the most appropriate for the application as tool electrode material in S-EDM. Additionally, there are no suitable EDM process parameters in order to benefit from the material characteristics of the respective tungsten carbide-cobalt. Focus of this work is the analysis of different tungsten carbide grades regarding the average grain size and the cobalt content in order to identify correlations between the material characteristics and the EDM process results. Therefore, eight different tungsten carbide grades with four different grain sizes and five different cobalt contents were applied in S-EDM experimental analysis. The experimental studies showed a general suitability of tungsten carbide-cobalt tool electrodes for EDM-processing, where the material removal rate is comparable to commonly used tool electrode materials. Nevertheless, the relative tool wear shows inferior results. It could be observed that higher cobalt content and coarser grain size of the applied tungsten carbide tool electrodes are advantageous for S-EDM.
  • Publication
    Optimization with the evolution strategy by example of electrical-discharge drilling
    ( 2020)
    Streckenbach, Jan
    ;
    Koref, Ivan Santibáñez
    ;
    Rechenberg, Ingo
    ;
    Uhlmann, Eckart
    A key challenge in electrical discharge machining (EDM) is to find a suitable combination out of numerous process parameters. Any changes concerning the electrode materials or geometries require newly optimized technologies. These technologies are to be developed from a considerable number of experiments which must be carried out by an experienced operator. This paper presents a new method of finding the optimal set of parameters. Here, the performance of the evolution strategy (ES), a stochastic, metaheuristic optimization method, is investigated. It offers the great advantage of finding solutions, even with little knowledge of system behaviour. The method involved a randomized and a derandomized ES, based on a non-elitist (m,l)-ES with one parent and four children. The two ES were initialized from an unfavourable starting point (A) and from a favourable starting point (B) to investigate their effectiveness. It could be demonstrated that starting from the unfavourable starting point A the erosion duration tero could be reduced by a maximum of 77% with a slightly smaller linear wear of the tool electrode DlE after 40 trials.
  • Publication
    Application of additive manufactured tungsten carbide tool electrodes in EDM
    ( 2018)
    Uhlmann, Eckart
    ;
    Bergmann, André
    ;
    Bolz, Robert
    ;
    Gridin, Witalij
    Application fields of electrical discharge machining (EDM) are limited due to given process conditions. When producing structures of high aspect ratios or using multi-axis machining, removed particles assemble at the machining zone, leading to process instabilities. A promising approach to improve EDM process conditions is the utilization of flushing channels in the tool electrode. However, with increasing complexity of the electrode geometry and the local integration of the mentioned flushing channels, conventional electrode manufacturing reaches its limitations. By applying Selective Laser Melting (SLM), these limitations are eliminated. The appropriate integration of flushing channels, even for complicated electrode geometries, improves process conditions during EDM in a variety of applications, leading to a higher material removal rate VW and reduced tool wear TH compared to machining without flushing. Additionally, the number of required tool electrodes can be reduced, as SLM enables an efficient integration and miniaturization of all features in a single electrode. Of particular interest in the field of EDM is carbide. Because of its wear resistance and stability, it is an ideal electrode material, which is commonly applied in mEDM. Tungsten carbide-cobalt is representative for this group of materials, which is already used in tool manufacturing. Several tests show a general suitability of carbide tool electrodes made by SLM for EDM-processing. However, the SLM process parameters and the composition of the carbide-cobalt show significant impact to the EDM results. A lower proportion of cobalt leads to reduced material removal rates VW and rising tool wear.