Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters
Reset filters

Settings
Now showing 1 - 6 of 6
  • Publication
    Echtzeit-Energieüberwachung in der Funkenerosion
    ( 2023)
    Uhlmann, Eckart
    ;
    Polte, Mitchel
    ;
    Yabroudi, Sami
    ;
    Thißen, Kai
    ;
    Penske, Wilhelm
    Ein großes Optimierungspotenzial der Funkenerosion liegt in den Energien der einzelnen Entladungen verborgen. Eine vektorielle Bestimmung der Entladedauern und die darauf basierende Energieberechnung sowie Klassifizierung erlauben es, die Entladeenergien, Entladungsarten und -dauern in Echtzeit zu überwachen und zu analysieren. Möglich wird dies durch ein Multiprocessing-Erzeuger-Verbraucher-Schema, welches überdies eine Visualisierung und Auswertung der Messdaten erlaubt.
  • Publication
    High-Performance Electro-Discharge Drilling with a Novel Type of Oxidized Tool Electrode
    ( 2022)
    Uhlmann, Eckart
    ;
    Polte, Julian
    ;
    Streckenbach, Jan
    ;
    Dinh, Ngoc Chuong
    ;
    Yabroudi, Sami
    ;
    Polte, Mitchel
    ;
    Börnstein, Julian
    Electro-discharge drilling is a key technology for manufacturing sophisticated nozzles in a broad range of automotive and aerospace applications. The formation of debris in the working gap leads to arcs and short circuits on the lateral surface when state-of-the-art tool electrodes are used. As a result, limited drilling depth, increased linear tool wear, and the conicity of boreholes are still challenges. In this work, a new approach for the passivation of the lateral surface of copper tool electrodes by oxidation is shown. The comparison with state-of-the-art tool electrodes showed a reduction in the erosion duration by 48% for machining hardened steel. Promising improvements could be achieved by the thermal oxidation of the tool electrodes with the aim of increasing the electrical resistivity of the lateral surface of the tool electrode. However, due to the loss of strength, the high oxide layer thickness, and the partial delamination of the oxide layer, further comprehensive investigations on the influence of the oxidation temperature need to be conducted. Future adjustments with lower oxidation temperatures will be carried out.
  • Publication
    Modeling of the wet immersed tumbling process with the Discrete Element Method (DEM)
    ( 2021)
    Uhlmann, Eckart
    ;
    Fürstenau, J.-P.
    ;
    Kuche, Yves
    ;
    Yabroudi, Sami
    ;
    Polte, Julian
    ;
    Polte, Mitchel
    Immersed tumbling is an industrially established process for finishing of components made of metal, ceramic or plastic. In this process, the components are completely surrounded by a wet, abrasive medium, which allows burrs to be removed and surfaces to be polished. In order to gain specific insights into the influence and flow properties of the abrasive media used in this process, numerical approaches using the Discrete Element Method (DEM) with the Rocky DEM software are presented within these investigations. A complete process simulation could be realised by means of a digital machine tool. The immersed tumbling process with cone-shaped polymer abrasive media is implemented by use of a liquid bridge model. The results were validated by experiments with an industrially used immersed tumbling machine tool and for the first time allow sound statements about the contact conditions and interactions of the abrasive media with the workpiece.
  • Publication
    Dry-ED milling of micro-scale contours with high-speed rotating tungsten tube electrodes
    ( 2020)
    Uhlmann, Eckart
    ;
    Perfilov, I.
    ;
    Yabroudi, Sami
    ;
    Mevert, Ricardo
    ;
    Polte, Mitchel
    This paper presents machining results for dry-ED milling of micro-scale contours by use of a new machine tool, including a relaxation generator, designed for dry-EDM. To implement the dry-ED milling process tungsten tube electrodes were used. The gas is injected through the tubular tool electrode under high pressure. Additionally, a high-speed EDM spindle was used to overcome process instabilities and increase the material removal rate due to better flushing conditions. Further, fluid simulations of the flushing conditions are presented in this paper. It is found that the use of gaseous dielectrics enables much better machining results in terms of shape accuracy and tool wear. The simulations provide new insights in the flushing conditions when using gaseous dielectrics. The calculated fluid flow pattern shows a great agreement with the observed depositions of reattached molten material on the tool and workpiece surface. The results presented as well as the hardware introduced enable the industrial application of dry-EDM for the first time.
  • Publication
    Electrical discharge dressing of honing stones
    ( 2020)
    Uhlmann, Eckart
    ;
    Yabroudi, Sami
    ;
    Zimmermann, Sascha
    ;
    Gerlitzky, Georg
    ;
    Polte, Mitchel
    ;
    Klink, Ulrich
    ;
    Sihling, Bernd
    Honing processes require a systematic preparation and a regeneration of the honing tool to guarantee a sufficient cutting behaviour and prevent unintended wear of the tool. These dressing processes are particularly important for the regeneration of the macro- and microscopic topography of the honing stones. The established method of manual shaping subsequent to a cylindrical grinding process demands a high skill level, a great amount of non-productive time and is not reproducible. In this paper the preparation of honing stones by use of electrical discharge machining (EDM) is presented. The aim is to ensure an automatic, systematic and reproducible process of resetting the bond of honing stones. Different tool electrode materials were analysed systematically for two different bond specifications of the honing stones. EDM process parameters were studied within a design of experiments (DoE) strategy and a subsequent effect analysis to assure the identification of most appropriate EDM process parameters. After this procedure various cycles of long-stroke honing processes were carried out. As a result, the new approach makes it possible to prepare honing stones with reproducible sharpness and macroscopic topography within an automated process. The dressing time td was reduced by 88 % compared to the established method.
  • Publication
    Application of additive manufactured tungsten carbide-cobalt electrodes with interior flushing channels in S-EDM
    ( 2020)
    Uhlmann, Eckart
    ;
    Polte, Julian
    ;
    Bolz, Robert
    ;
    Yabroudi, Sami
    ;
    Streckenbach, Jan
    ;
    Bergmann, André
    Application fields of electrical discharge machining (EDM) are limited due to given process conditions. Manufacturing of parts with high aspect ratios and the application of multi-axis machining are limited due to process instabilities caused by removed particles. A promising approach to improve EDM process conditions, especially in sinking EDM (S-EDM), is the utilization of flushing channels in the tool electrode. However, with increasing complexity of the tool electrode geometry and the local integration of these flushing channels, conventional tool electrode manufacturing by cutting is limited. In contrast to that, the machining process selective laser melting (SLM) does not have such limitations. The appropriate integration of flushing channels, even for complex electrode geometries, improves process conditions during EDM in a variety of applications. This leads to a higher material removal rate and reduced tool wear compared to machining without flushing. Additionally, the number of required tool electrodes can be reduced, as SLM enables an efficient integration and miniaturization of all features in a single electrode. Because of its wear resistance and stability, tungsten carbide is an ideal tool electrode material, which is commonly applied in drilling EDM. After identifying suitable process parameters for roughing EDM with additively manufactured tungsten carbide cobalt tool electrodes, different forms of flushing channels were analysed in order to establish a fast process with minimum tool electrode wear. The results concerning material removal rate and the relative tool wear could be improved by applying internal flushing, though the tool wear stayed at a worse level compared to conventional tool electrode materials.