Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters

28
Reset filters

Settings
Now showing 1 - 10 of 28
  • Publication
    AI-based welding process monitoring for quality control in large-diameter pipe manufacturing
    ( 2024-04-25)
    Gook, Sergej
    ;
    El-Sari, Bassel
    ;
    Biegler, Max
    ;
    Rethmeier, Michael
    The paper presents the experimental results into the development of a multi-channel system for monitoring and quality assurance of the multi-wire submerged arc welding (SAW) process for the manufacture of large diameter pipes. Process signals such as welding current, arc voltage and the acoustic signal emitted from the weld zone are recorded and processed to provide information on the stability of the welding process. It was shown by the experiments that the acoustic pattern of the SAW process in a frequency range between 30 Hz and 2.5 kHz contains the most diagnostic information. In the spectrogram of the acoustic signal, which represents the time course of the frequency spectrum of the welding process, the formation of weld irregularities such as undercuts could be reliably identified. The on-line quality assessment of the weld seam produced is carried out in combination with methods of artificial intelligence (AI). From the results obtained, it can be concluded that the use of the latest concepts in welding and automation technology, combined with the high potential of AI, can achieve a new level of quality assurance in pipe manufacturing.
  • Publication
    KI zur Prozessüberwachung im Unterpulverschweißen
    ( 2024-01-15)
    El-Sari, Bassel
    ;
    Gook, Sergej
    ;
    Biegler, Max
    ;
    Rethmeier, Michael
    Beim Unterpulverschweißen sind die Prozessgeräusche ein Indikator für eine gute Fügequalität. Diese Beurteilung kann i.d.R. nur von einer erfahrenen Fachkraft durchgeführt werden. Eine kürzlich entwickelte künstliche Intelligenz kann automatisch das akustische Prozesssignal anhand vortrainierter Merkmale klassifizieren und die Fügequalität anhand des Geräuschs beurteilen. Der Algorithmus, einmal richtig trainiert, kann den Prüfaufwand beim Unterpulverschweißen deutlich reduzieren.
  • Publication
    Kombination des Laserhybridschweißens und UP-Engspaltschweißens für dickwandige Bauteile zur Erhöhung der Wirtschaftlichkeit
    ( 2024)
    Gook, Sergej
    ;
    El-Sari, Bassel
    ;
    Üstündag, Ömer
    ;
    Gumenyuk, Andrey
    ;
    Biegler, Max
    ;
    Rethmeier, Michael
    Dieser Beitrag befasst sich mit der Entwicklung eines wirtschaftlichen und robusten Verfahrens zum Schweißen dicker Stahlbleche. Es werden Ergebnisse für das Fügen von Blechen im Dickenbereich von 25 mm bis 80 mm vorgestellt. Die 30 mm dicken Schweißnähte konnten im Stumpfstoß in zwei Durchgängen unter Verwendung des Laserhybridschweißens und des Unterpulverschweißens (UP) geschweißt werden. Das Laserhybridschweißen wird als Einschweißung mit einer Tiefe von ca. 25 mm ausgeführt. Die UP-Lagen werden auf der gegenüberliegenden Seite des Blechs aufgebracht. Bei richtiger Wahl der Schweißparameter wird der Nahtquerschnitt durch eine sichere Überlappung beider Lagen geschlossen. Bei Blechdicken über 30 mm ist eine Kantenvorbereitung erforderlich, die eine Ausführung der UP-Fülllagen in Engspalttechnik ermöglicht. Die Vorteile der vorgeschlagenen Prozesskombination liegen darin, dass die Nahtwurzel der Laserhybridnaht nicht geformt werden muss. Defekte in der Wurzel der Laserhybrideinschweißung können durch die UP-Lagen effektiv beseitigt werden. Das Verfahren bietet eine hohe Stabilität des Schweißprozes-ses in Bezug auf die Qualität der Blechkanten. Plasmageschnittene Kanten konnten ohne Bindefehler geschweißt werden. Die erreichte Nahtqualität wurde durch zerstörende und zerstörungsfreie Prüfungen bestätigt.
  • Publication
    Laserstrahlhybridschweissen von Türmen für Windkraftanlagen - Ökonomische und ökologische Vorteile
    ( 2023-12-19)
    Üstündag, Ömer
    ;
    Bakir, Nasim
    ;
    Brunner-Schwer, Christian
    ;
    Knöfel, Frieder
    ;
    Gook, Sergej
    ;
    Gumenyuk, Andrey
    ;
    Rethmeier, Michael
    Das Laserstrahlhybridschweißen ist beim Schweißen von Türmen für Windkraftanlagen eine Alternative zum Unterpulver schweißen von Dickblechen in Mehrlagentechnik und bietet hier ökonomische und ökologische Vorteile. Der industrielle Einsatz des Verfahrens ist jedoch durch prozessspezifische Herausforderungen eingeschränkt. Die im Beitrag beschriebene kontaktlose elektromagnetische Badstütze dient zur Erweiterung des Verfahrenspotenzials im Dickblechbereich >15 mm.
  • Publication
    Retaining Mechanical Properties of GMA-Welded Joints of 9%Ni Steel Using Experimentally Produced Matching Ferritic Filler Metal
    ( 2022-11-30)
    El-batahgy, Abdel-monem
    ;
    Elkousy, Mohamed Raafat
    ;
    Al-Rahman, Ahmed Abd
    ;
    Gumenyuk, Andrey
    ;
    Rethmeier, Michael
    ;
    Gook, Sergej
    Motivated by the loss of tensile strength in 9%Ni steel arc-welded joints performed using commercially available Ni-based austenitic filler metals, the viability of retaining tensile strength using an experimentally produced matching ferritic filler metal was confirmed. Compared to the austenitic Ni-based filler metal (685 MPa), higher tensile strength in gas metal arc (GMA) welded joints was achieved using a ferritic filler metal (749 MPa) due to its microstructure being similar to the base metal (645 MPa). The microstructure of hard martensite resulted in an impact energy of 71 J (−196 °C), which was two times higher than the specified minimum value of ≥34 J. The tensile and impact strength of the welded joint is affected not only by its microstructure, but also by the degree of its mechanical mismatch depending on the type of filler metal. Welds with a harder microstructure and less mechanical mismatch are important for achieving an adequate combination of tensile strength and notched impact strength. This is achievable with the cost-effective ferritic filler metal. A more desirable combination of mechanical properties is guaranteed by applying low preheating temperature (200 °C), which is a more practicable and economical solution compared to the high post-weld heat treatment (PWHT) temperature (580 °C) suggested by other research.
  • Publication
    Laserstrahlhybridschweißen von Türmen für Windkraftanlagen
    ( 2022-08-29)
    Üstündag, Ömer
    ;
    Bakir, Nasim
    ;
    Brunner-Schwer, Christian
    ;
    Knöfel, Frieder
    ;
    Gook, Sergej
    ;
    Rethmeier, Michael
    ;
    Gumenyuk, Andrey
    Das Laserstrahlhybridschweißen ist beim Schweißen von Türmen für Windkraftanlagen eine Alternative zum Unterpulverschweißen von Dickblechen in Mehrlagentechnik und bietet hier ökonomische und ökologische Vorteile. Der industrielle Einsatz des Verfahrens ist jedoch durch prozessspezifische Herausforderungen eingeschränkt. Die im Beitrag beschriebene kontaktlose elektromagnetische Badstütze dient zur Erweiterung des Verfahrenspotenzials im Dickblechbereich >15 mm.
  • Publication
    Joining 30 mm Thick Shipbuilding Steel Plates EH36 Using a Process Combination of Hybrid Laser Arc Welding and Submerged Arc Welding
    ( 2022-08-04)
    Gook, Sergej
    ;
    Midik, Ahmet
    ;
    Biegler, Max
    ;
    Gumenyuk, Andrey
    ;
    Rethmeier, Michael
    This article presents a cost-effective and reliable method for welding 30 mm thick sheets of shipbuilding steel EH36. The method proposes to perform butt welding in a two-run technique using hybrid laser arc welding (HLAW) and submerged arc welding (SAW). The HLAW is performed as a partial penetration weld with a penetration depth of approximately 25 mm. The SAW is carried out as a second run on the opposite side. With a SAW penetration depth of 8 mm, the weld cross-section is closed with the reliable intersection of both passes. The advantages of the proposed welding method are: no need for forming of the HLAW root; the SAW pass can effectively eliminate pores in the HLAW root; the high stability of the welding process regarding the preparation quality of the weld edges. Plasma cut edges can be welded without lack of fusion defects. The weld quality achieved is confirmed by destructive tests.
  • Publication
    Material-adapted and process-reliable multi-wire submerged arc welding of large-diameter pipes
    ( 2022-03-07)
    Gook, Sergej
    ;
    El-Sari, Bassel
    ;
    Biegler, Max
    ;
    Rethmeier, Michael
    ;
    Lichtenthäler, Frank
    ;
    Stark, Michael
    Ensuring the required mechanical-technological properties of welds is a critical issue in the application of multi-wire submerged arc welding processes in the manufacture of largediameter pipes made of high-strength fine-grained steels of grade X70 and higher according to API 5L. Excessive heat input of up to 10 kJ/mm is one of the main causes of the formation of microstructural areas in the heat-affected zone with deteriorated mechanical properties, such as impact toughness and tensile strength. In this work, a variant of a five-wire submerged arc welding process is proposed that reduces the weld volume and the heat input, while retaining the high process stability and production speed of multi-wire submerged arc welding. By adapting the welding wire configuration of a five-wire submerged arc welding process and the energetic parameters of the arcs, the high penetration depth of approx. 24 mm and a 10 % reduction in the weld cross-section could be achieved compared to the usual process configuration. This effect was transformed into a higher welding speed, which led to a reduction in the heat input. A concept for process monitoring is proposed in order to maintain constant manufacturing quality in large-diameter pipe production. In addition to the analysis of electrical process signals such as welding current and welding voltage, acoustic process monitoring using vibro-acoustic sensors provides reliable information on the stability of the welding process.
  • Publication
    Багатодротове дугове зварювання високоміцних дрібнозернистих сталей під флюсом
    ( 2022)
    Gook, Sergej
    ;
    El-Sari, Bassel
    ;
    Biegler, Max
    ;
    Rethmeier, Michael
    ;
    Lichtenthäler, F.
    ;
    Stark, M.
    Ensuring the required mechanical-technological properties of welds is a critical issue in the application of multi-wire submerged arc welding process for welding high-strength fine-grained steels. Excessive heat input is one of the main causes for microstructural zones with deteriorated mechanical properties of the welded joint, such as a reduced notched impact strength and a lower structural robustness. A process variant is proposed which reduces the weld volume as well as the heat input by adjusting the welding wire configuration as well as the energetic parameters of the arcs, while retaining the advantages of multi-wire submerged arc welding such as high process stability and production speed
  • Publication
    Hybrid Laser-Arc Welding of Thick-Walled, Closed, Circumferential Pipe Welds
    ( 2022)
    Üstündag, Ömer
    ;
    Bakir, Nasim
    ;
    Gook, Sergej
    ;
    Gumenyuk, Andrey
    ;
    Rethmeier, Michael
    The application of hybrid laser-arc welding (HLAW) for joining closed circumferential welds is a challenge due to the high risk of forming a defective overlap area with a shrinkage void or solidification cracks in the material thickness. A series of HLAW experiments were performed to understand the development of a faulty overlap area when closing the circumferential weld. Welding trials on flat specimens and pipe segments were supported by numerical analyses in which the thermomechanical behavior of the welds in the overlap area was investigated. Different process control strategies were tested, including variations in defocusing levels and the overlap length. The newly developed HLAW head, including laser optics with a motor-driven collimation system, made it possible to defocus the laser beam during welding without disturbing the stability of the welding process. High-level defocusing of the laser beam of more than 40 mm relative to the specimen surface with a resulting beam diameter of > 2.9 mm, and in combination with a short overlap length of 15 mm, was promising with respect to the formation of a desired cup-shaped weld profile that is resistant to solidification cracks.