Now showing 1 - 10 of 2902
  • Publication
    Multiple-Wire Submerged Arc Welding of High-Strength Fine-Grained Steels
    ( 2022)
    Gook, S.
    ;
    ; ; ;
    Lichtenthäler, F.
    ;
    Stark, M.
    Ensuring the required mechanical-technological properties of welds is a critical issue in the application of multi-wire submerged arc welding process for welding high-strength fine-grained steels. Excessive heat input is one of the main causes for microstructural zones with deteriorated mechanical properties of the welded joint, such as a reduced notched impact strength and a lower structural robustness. A process variant is proposed which reduces the weld volume as well as the heat input by adjusting the welding wire configuration as well as the energetic parameters of the arcs, while retaining the advantages of multi-wire submerged arc welding such as high process stability and production speed.
  • Publication
    Methodology for a reverse engineering process chain with focus on customized segmentation and iterative closest point algorithms
    ( 2022) ;
    Schröder, Robert
    ;
    Stark, Rainer
    One-off construction is characterized by a multiplicity of manual manufacturing processes whereby it is based on consistent use of digital models. Since the actual state of construction does not match the digital models without manually updating them, the authors propose a method to automatically detect deviations and reposition the model data according to reality. The first essential method is based on the ""Segmentation of Unorganized Points and Recognition of Simple Algebraic Surfaces"" presented by Vanco et al.. The second method is the customization of the iterative closest point (ICP) algorithm. The authors present the overall structure of the implemented software, based on open source and relate it to the general reverse engineering (RE) framework by Buonamici et al.. A highlight will be given on: the general architecture of the software prototype; a customized segmentation and clustering of unorganized points and recognition of simple algebraic surfaces; the deviation analysis with a customized iterative closest point (CICP) algorithm Especially in the field of one-off construction, characterized by small and medium companies, automated assessment of 3D scan data during the design process is still in its infancy. By using an open source environment progress for consistent use of digital models could be accelerated.
  • Publication
    Untersuchungen zur Beeinflussung der Geometrie und Werkstoffeigenschaften laserimplantierter Werkzeugstahloberflächen sowie zum tribologischen Einsatzverhalten
    (Fraunhofer Verlag, 2022)
    Spranger, Felix
    In einer Vielzahl technischer Anwendungen spielt die Schaffung und Aufrechterhaltung eines definierten tribologischen Verhaltens zwischen in Kontakt tretenden Wirkflächen für die Funktionalität von Bauteilen oder Werkzeugen eine entscheidende Rolle. Verfahren der Oberflächentechnik verfolgen das Ziel, entweder durch eine Manipulation der Werkstoffeigenschaften oder durch eine Strukturierung der Wirkfächen diese anzupassen. Obwohl erhabene Mikrostrukturen großes Potenzial zur gezielten Manipulation zeigen, wurden diese bislang wenig betrachtet, da sie anfällig für Verschleiß sind und nur schwer hergestellt werden können. Mit der Laserimplantation ist ein Verfahren bekannt, welches diese Hemmnisse überwindet und eine Generierung verschleißbeständiger, erhabener Mikrostrukturen (Implants) durch ein gepulstes Laserdispergieren keramischer Hartstoffpartikel in Wirkflächen zulässt. Um eine breite Nutzbarkeit zu erreichen, wird in dieser Arbeit eine Erweiterung des Prozessverständnisses forciert, sodass die geometrischen als auch werkstofftechnischen Implanteigenschaften zielgerichtet manipulierbar werden. Des Weiteren wird die tribologische Wirkweise implantierter Oberflächen betrachtet.
  • Publication
    Багатодротове дугове зварювання високоміцних дрібнозернистих сталей під флюсом
    ( 2022) ; ; ; ;
    Lichtenthäler, F.
    ;
    Stark, M.
    Ensuring the required mechanical-technological properties of welds is a critical issue in the application of multi-wire submerged arc welding process for welding high-strength fine-grained steels. Excessive heat input is one of the main causes for microstructural zones with deteriorated mechanical properties of the welded joint, such as a reduced notched impact strength and a lower structural robustness. A process variant is proposed which reduces the weld volume as well as the heat input by adjusting the welding wire configuration as well as the energetic parameters of the arcs, while retaining the advantages of multi-wire submerged arc welding such as high process stability and production speed
  • Publication
    Wolframschmelzcarbidbasierte MMC-Schichten für den industriellen Einsatz im Formenbau
    ( 2022)
    Langebeck, Anika
    ;
    Jahnke, Christian
    ;
    Wünderlich, Tim
    ;
    ;
    Bohlen, Annika
    ;
    Zur Steigerung der abrasiven Verschleißbeständigkeit können Oberflächen lokal mit Hartpartikeln verstärkt werden. Diese sogenannten Metal-Matrix-Composit(MMC)-Schichten können mittels Laserstrahldispergieren gefertigt und durch Mikrofräsen nachbearbeitet werden. Im hier vorgestellten Forschungsvorhaben wurde als Grundwerkstoff verwendete Aluminiumbronze (CuAl10Ni5Fe4) mit Wolframschmelzcarbid verstärkt. Der Hartpartikelgehalt kann dabei durch eine Steigerung des Pulvermassenstroms bis zur Packungsdichte des unverarbeiteten Pulvers erhöht werden. Über eine temperaturbasierte Leistungsregelung kann eine gleichbleibend homogene MMC-Schicht mit konstanter Dicke und Tiefe dispergiert werden. Durch das Mikrofräsen mit optimierten Parametern können qualitativ hochwertige MMC-Oberflächen für den industriellen Einsatz in Spritzgusswerkzeugen hergestellt werden. Dabei wurde vor allem der Zahnvorschub fz als kritischer Prozessparameter identifiziert.
  • Publication
    Study on the transition behavior of the bulging effect during deep penetration laser beam welding
    ( 2022)
    Artinov, A.
    ;
    Meng, X.
    ;
    Bachmann, M.
    ;
    Rethmeier, M.
    The present work is devoted to the study of the transition behavior of the recently confirmed widening of the weld pool, known as the bulging effect, during high-power deep penetration laser beam welding of thick unalloyed steel sheets. A three-dimensional transient multi-physics numerical model is developed, allowing for the prediction of the bulge formation and the study of its temporal behavior. The model is generalized to account automatically for the transition from partial to complete penetration. Several experimental measurements and observations, such as drilling period, weld pool length, temperature, efficiency, and metallographic cross-sections are used to verify the model and assure the plausibility of the numerical results. The analysis of the calculated temperature and velocity distributions, as well as the evolution of the keyhole geometry, show that the formation of a bulging region strongly depends on the penetration depth of the weld. Based on the numerical results, the bulge is found to occur transiently, having its transition from a slight bulge to a fully developed bulging between penetration depths of 6 mm and 9 mm, respectively.
  • Publication
    Numerical investigation into cleanability of support structures produced by powder bed fusion technology
    ( 2022)
    Campana, Giampaolo
    ;
    ;
    Mele, Mattia
    ;
    Raffaelli, Luca
    ;
    Bergmann, André
    ;
    ;
    Purpose: Support structures used in laser powder bed fusion are often difficult to clean from unsintered powder at the end of the process. This issue can be significantly reduced through a proper design of these auxiliary structures. This paper aims to investigate preliminary the airflow within differently oriented support structures and to provide design guidelines to enhance their cleanability, especially the depowdering of them. Design/methodology/approach: This study investigates the cleanability of support structures in powder bed fusion technology. Digital models of cleaning operations were designed through computer-aided engineering systems. Simulations of the airflow running into the powder entrapped within the thin walls of auxiliary supports were implemented by computational fluid dynamics. This approach was applied to a set of randomly generated geometrical configurations to determine the air turbulence intensity depending on their design. Findings: The resul ts, which are based on the assumption that a relationship exists between turbulence and powder removal effectiveness, demonstrated that the maximum cleanability is obtainable through specific relative rotations between consecutive support structures. Furthermore, it was possible to highlight the considerable influence of the auxiliary structures next to the fluid inlet. These relevant findings establish optimal design rules for the cleanability of parts manufactured by powder bed fusion processes. Originality/value: This study presents a preliminary investigation into the cleanability of support structures in laser powder bed fusion, which has not been addressed by previous literature. The results allow for a better understanding of the fluid dynamics during cleaning operations. New guidelines to enhance the cleanability of support structures are provided based on the results of simulations.
  • Publication
    Optimizing the sharpening process of hybrid-bonded diamond grinding wheels by means of a process model
    ( 2022) ;
    Muthulingam, Arunan
    The grinding wheel topography influences the cutting performance and thus the economic efficiency of a grinding process. In contrary to conventional grinding wheels, super abrasive grinding wheels should undergo an additional sharpening process after the initial profiling process to obtain a suitable microstructure of the grinding wheel. Due to the lack of scientific knowledge, the sharpening process is mostly performed manually in industrial practice. A CNC-controlled sharpening process can not only improve the reproducibility of grinding processes but also decrease the secondary processing time and thereby increase the economic efficiency significantly. To optimize the sharpening process, experimental investigations were carried out to identify the significant sharpening parameters influencing the grinding wheel topography. The sharpening block width lSb, the grain size of the sharpening block dkSb and the area-related material removal in sharpening VâSb were identi fied as the most significant parameters. Additional experiments were performed to further quantify the influence of the significant sharpening parameters. Based on that, a process model was developed to predict the required sharpening parameters for certain target topographies. By using the process model, constant work results and improved process reliability can be obtained.
  • Publication
    Effects on crack formation of additive manufactured Inconel 939 sheets during electron beam welding
    ( 2022)
    Raute, Julius
    ;
    Jokisch, Torsten
    ;
    ;
    The potential of additive manufacturing for processing precipitation hardened nickel-base superalloys, such as Inconel 939 is considerable, but in order to fully exploit this potential, fusion welding capabilities for additive parts need to be explored. Currently, it is uncertain how the different properties from the additive manufacturing process will affect the weldability of materials susceptible to hot cracking. Therefore, this work investigates the possibility of joining additively manufactured nickel-based superalloys using electron beam welding. In particular, the influence of process parameters on crack formation is investigated. In addition, hardness measurements are performed on cross-sections of the welds. It is shown that cracks at the seam head are enhanced by welding speed and energy per unit length and correlate with the hardness of the weld metal. Cracking parallel to the weld area shows no clear dependence on the process variables that have been investigated, but is related to the hardness of the heat-affected zone.
  • Publication
    PowerGrasp: Development Aspects for Arm Support Systems
    ( 2022)
    Goppold, J.-P.
    ;
    Kuschan, J.
    ;
    Schmidt, H.
    ;
    Krüger, J.
    Exoskeletons can support workers on physically demanding tasks, but in industry they lack of acceptance. This contribution gives an insight into design aspects for upper body exoskeletons, especially how active exoskeletons for industrial applications differ from military and medical use-cases. To overcome typical rigid exoskeleton problems, we suggest the use of modular soft-exosuit support systems and therefore checked different types of soft actuation principles for their eligibility for the use on upper body joints. Most promising approach is using two-layered actuators sting of robust fabric with embedded rubber tubes as pressure chambers. By inflating the tubes, it is possible to vary the stiffness of the chambers, which can be effectively used to generate assisting forces and moments at human joints (shoulder, elbow, wrist, finger).