Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters
Reset filters

Settings
Now showing 1 - 10 of 1215
No Thumbnail Available
Publication

Multiple-Wire Submerged Arc Welding of High-Strength Fine-Grained Steels

2022 , Gook, S. , El-Sari, Bassel , Biegler, Max , Rethmeier, Michael , Lichtenthäler, F. , Stark, M.

Ensuring the required mechanical-technological properties of welds is a critical issue in the application of multi-wire submerged arc welding process for welding high-strength fine-grained steels. Excessive heat input is one of the main causes for microstructural zones with deteriorated mechanical properties of the welded joint, such as a reduced notched impact strength and a lower structural robustness. A process variant is proposed which reduces the weld volume as well as the heat input by adjusting the welding wire configuration as well as the energetic parameters of the arcs, while retaining the advantages of multi-wire submerged arc welding such as high process stability and production speed.

View
No Thumbnail Available
Publication

Methodology for a reverse engineering process chain with focus on customized segmentation and iterative closest point algorithms

2022 , Mönchinger, Stephan , Schröder, Robert , Stark, Rainer

One-off construction is characterized by a multiplicity of manual manufacturing processes whereby it is based on consistent use of digital models. Since the actual state of construction does not match the digital models without manually updating them, the authors propose a method to automatically detect deviations and reposition the model data according to reality. The first essential method is based on the ""Segmentation of Unorganized Points and Recognition of Simple Algebraic Surfaces"" presented by Vanco et al.. The second method is the customization of the iterative closest point (ICP) algorithm. The authors present the overall structure of the implemented software, based on open source and relate it to the general reverse engineering (RE) framework by Buonamici et al.. A highlight will be given on: the general architecture of the software prototype; a customized segmentation and clustering of unorganized points and recognition of simple algebraic surfaces; the deviation analysis with a customized iterative closest point (CICP) algorithm Especially in the field of one-off construction, characterized by small and medium companies, automated assessment of 3D scan data during the design process is still in its infancy. By using an open source environment progress for consistent use of digital models could be accelerated.

View
No Thumbnail Available
Publication

Effects on crack formation of additive manufactured Inconel 939 sheets during electron beam welding

2022 , Raute, Julius , Jokisch, Torsten , Biegler, Max , Rethmeier, Michael

The potential of additive manufacturing for processing precipitation hardened nickel-base superalloys, such as Inconel 939 is considerable, but in order to fully exploit this potential, fusion welding capabilities for additive parts need to be explored. Currently, it is uncertain how the different properties from the additive manufacturing process will affect the weldability of materials susceptible to hot cracking. Therefore, this work investigates the possibility of joining additively manufactured nickel-based superalloys using electron beam welding. In particular, the influence of process parameters on crack formation is investigated. In addition, hardness measurements are performed on cross-sections of the welds. It is shown that cracks at the seam head are enhanced by welding speed and energy per unit length and correlate with the hardness of the weld metal. Cracking parallel to the weld area shows no clear dependence on the process variables that have been investigated, but is related to the hardness of the heat-affected zone.

View
No Thumbnail Available
Publication

Optimizing the sharpening process of hybrid-bonded diamond grinding wheels by means of a process model

2022 , Uhlmann, E. , Muthulingam, A.

The grinding wheel topography influences the cutting performance and thus the economic efficiency of a grinding process. In contrary to conventional grinding wheels, super abrasive grinding wheels should undergo an additional sharpening process after the initial profiling process to obtain a suitable microstructure of the grinding wheel. Due to the lack of scientific knowledge, the sharpening process is mostly performed manually in industrial practice. A CNC-controlled sharpening process can not only improve the reproducibility of grinding processes but also decrease the secondary processing time and thereby increase the economic efficiency significantly. To optimize the sharpening process, experimental investigations were carried out to identify the significant sharpening parameters influencing the grinding wheel topography. The sharpening block width lSb, the grain size of the sharpening block dkSb and the area-related material removal in sharpening VâSb were identi fied as the most significant parameters. Additional experiments were performed to further quantify the influence of the significant sharpening parameters. Based on that, a process model was developed to predict the required sharpening parameters for certain target topographies. By using the process model, constant work results and improved process reliability can be obtained.

View
No Thumbnail Available
Publication

In situ microstructure analysis of Inconel 625 during laser powder bed fusion

2022 , Schmeiser, F. , Krohmer, E. , Wagner, C. , Schell, N. , Uhlmann, E. , Reimers, W.

Laser powder bed fusion is an additive manufacturing process that employs highly focused laser radiation for selective melting of a metal powder bed. This process entails a complex heat flow and thermal management that results in characteristic, often highly textured microstructures, which lead to mechanical anisotropy. In this study, high-energy X-ray diffraction experiments were carried out to illuminate the formation and evolution of microstructural features during LPBF. The nickel-base alloy Inconel 625 was used for in situ experiments using a custom LPBF system designed for these investigations. The diffraction patterns yielded results regarding texture, lattice defects, recrystallization, and chemical segregation. A combination of high laser power and scanning speed results in a strong preferred crystallographic orientation, while low laser power and scanning speed showed no clear texture. The observation of a constant gauge volume revealed solid-state texture changes without remelting. They were related to in situ recrystallization processes caused by the repeated laser scanning. After recrystallization, the formation and growth of segregations were deduced from an increasing diffraction peak asymmetry and confirmed by ex situ scanning transmission electron microscopy.

View
No Thumbnail Available
Publication

Hybrid laser-arc welding of laser- and plasma-cut 20-mm-thick structural steels

2022 , Üstündag, Ömer , Bakir, Nasim , Gook, Sergej , Gumenyuk, Andrey , Rethmeier, Michael

It is already known that the laser beam welding (LBW) or hybrid laser-arc welding (HLAW) processes are sensitive to manufacturing tolerances such as gaps and misalignment of the edges, especially at welding of thick-walled steels due to its narrow beam diameter. Therefore, the joining parts preferably have to be milled. The study deals with the influence of the edge quality, the gap and the misalignment of edges on the weld seam quality of hybrid laser-arc welded 20-mm-thick structural steel plates which were prepared by laser and plasma cutting. Single-pass welds were conducted in butt joint configuration. An AC magnet was used as a contactless backing. It was positioned under the workpiece during the welding process to prevent sagging. The profile of the edges and the gap between the workpieces were measured before welding by a profile scanner or a digital camera, respectively. With a laser beam power of just 13.7 kW, the single-pass welds could be performed. A gap bridgeability up to 1 mm at laser-cut and 2 mm at plasma-cut samples could be reached respectively. Furthermore, a misalignment of the edges up to 2 mm could be welded in a single pass. The new findings may eliminate the need for cost and time-consuming preparation of the edges.

View
No Thumbnail Available
Publication

Wolframschmelzcarbidbasierte MMC-Schichten für den industriellen Einsatz im Formenbau

2022 , Langebeck, Anika , Jahnke, Christian , Wünderlich, Tim , Hein, Christoph , Bohlen, Annika , Uhlmann, Eckart

Zur Steigerung der abrasiven Verschleißbeständigkeit können Oberflächen lokal mit Hartpartikeln verstärkt werden. Diese sogenannten Metal-Matrix-Composit(MMC)-Schichten können mittels Laserstrahldispergieren gefertigt und durch Mikrofräsen nachbearbeitet werden. Im hier vorgestellten Forschungsvorhaben wurde als Grundwerkstoff verwendete Aluminiumbronze (CuAl10Ni5Fe4) mit Wolframschmelzcarbid verstärkt. Der Hartpartikelgehalt kann dabei durch eine Steigerung des Pulvermassenstroms bis zur Packungsdichte des unverarbeiteten Pulvers erhöht werden. Über eine temperaturbasierte Leistungsregelung kann eine gleichbleibend homogene MMC-Schicht mit konstanter Dicke und Tiefe dispergiert werden. Durch das Mikrofräsen mit optimierten Parametern können qualitativ hochwertige MMC-Oberflächen für den industriellen Einsatz in Spritzgusswerkzeugen hergestellt werden. Dabei wurde vor allem der Zahnvorschub fz als kritischer Prozessparameter identifiziert.

View
No Thumbnail Available
Publication

Study on the transition behavior of the bulging effect during deep penetration laser beam welding

2022 , Artinov, A. , Meng, X. , Bachmann, M. , Rethmeier, M.

The present work is devoted to the study of the transition behavior of the recently confirmed widening of the weld pool, known as the bulging effect, during high-power deep penetration laser beam welding of thick unalloyed steel sheets. A three-dimensional transient multi-physics numerical model is developed, allowing for the prediction of the bulge formation and the study of its temporal behavior. The model is generalized to account automatically for the transition from partial to complete penetration. Several experimental measurements and observations, such as drilling period, weld pool length, temperature, efficiency, and metallographic cross-sections are used to verify the model and assure the plausibility of the numerical results. The analysis of the calculated temperature and velocity distributions, as well as the evolution of the keyhole geometry, show that the formation of a bulging region strongly depends on the penetration depth of the weld. Based on the numerical results, the bulge is found to occur transiently, having its transition from a slight bulge to a fully developed bulging between penetration depths of 6 mm and 9 mm, respectively.

View
No Thumbnail Available
Publication

Characterization of Ti-6Al-4V Fabricated by Multilayer Laser Powder-Based Directed Energy Deposition

2022 , Ávila Calderón, Luis Alexander , Graf, Benjamin , Rehmer, Birgit , Petrat, Torsten , Skrotzki, Birgit , Rethmeier, Michael

Laser powder-based directed energy deposition (DED-L) is increasingly being used in additive manufacturing (AM). As AM technology, DED-L must consider specific challenges. It must achieve uniform volume growth over hundreds of layers and avoid heat buildup of the deposited material. Herein, Ti-6Al-4V is fabricated using an approach that addresses these challenges and is relevant in terms of transferability to DED-L applications in AM. The assessment of the obtained properties and the discussion of their relationship to the process conditions and resulting microstructure are presented. The quality of the manufacturing process is proven in terms of the reproducibility of properties between individual blanks and with respect to the building height. The characterization demonstrates that excellent mechanical properties are achieved at room temperature and at 400 C.

View
No Thumbnail Available
Publication

Hybrid Laser-Arc Welding of Thick-Walled, Closed, Circumferential Pipe Welds

2022 , Üstündag, Ömer , Bakir, Nasim , Gook, Sergej , Gumenyuk, Andrey , Rethmeier, Michael

The application of hybrid laser-arc welding (HLAW) for joining closed circumferential welds is a challenge due to the high risk of forming a defective overlap area with a shrinkage void or solidification cracks in the material thickness. A series of HLAW experiments were performed to understand the development of a faulty overlap area when closing the circumferential weld. Welding trials on flat specimens and pipe segments were supported by numerical analyses in which the thermomechanical behavior of the welds in the overlap area was investigated. Different process control strategies were tested, including variations in defocusing levels and the overlap length. The newly developed HLAW head, including laser optics with a motor-driven collimation system, made it possible to defocus the laser beam during welding without disturbing the stability of the welding process. High-level defocusing of the laser beam of more than 40 mm relative to the specimen surface with a resulting beam diameter of > 2.9 mm, and in combination with a short overlap length of 15 mm, was promising with respect to the formation of a desired cup-shaped weld profile that is resistant to solidification cracks.

View