Now showing 1 - 5 of 5
No Thumbnail Available
Publication

Gear Wheel Finishing with Abrasive Brushing Tools to Improve the Surface Quality of Tooth Flanks for the Industrial Application

2022 , Gülzow, Bernhard , Uhlmann, Eckart

A high surface quality of tooth flanks can improve the service life and the performance of gears, as well as reduce acoustic emissions. However, high demands on the gear geometry pose a challenge for the finishing of tooth flank surfaces because the dimensional accuracy that can be achieved with modern grinding processes must not be impaired by the finishing process. A preceding study has shown fundamentally that profiled abrasive brushing tools can be used to improve the quality of individual tooth flank surfaces. Due to the integration into the grinding machine, it represents a promising alternative to common finishing applications. Before the process can be used in an industrial environment, process reliability and tool life must be examined. For this purpose, complete reference gearwheels (39 × 10) were finished with the brushing tools. It could be shown that the surface roughness can be reliably reduced by ΔRa ≈ 0.2 µm by using a single brush for an entire gearwheel without changing the gear geometry. In addition to the influence of the tool specifications on the work result, the influence of the initial roughness after grinding was considered in particular. It was found that the achievable surface roughness depends significantly on the depth of the grinding grooves, as these are retained as desired, while the roughness peaks are fully smoothed. Furthermore, a device for the machine-integrated profiling and dressing of brushing tools was successfully designed, implemented, and tested.

No Thumbnail Available
Publication

Micro-texture dependent temperature distribution of CVD diamond thick film cutting tools during turning of Ti-6Al-4V

2022 , Uhlmann, Eckart , Schröter, D. , Gärtner, Eric

Machining titanium alloys such as Ti-6Al-4V results in a high thermomechanical load on cutting tools and consequently short tool lifes. With respect to a necessary reduction of the resulting cutting tool temperatures, ultrashort pulse (USP) laser fabricated micro-textured rake faces offer direct supply of cooling lubricant into the cutting zone and lead to a reduced heat induction. As a result, micro-textured CVD diamond thick film cutting tools are also capable of machining high-performance materials due to reduced contact temperatures. In the scope of the research, the resulting temperature distribution for micro-textured rake faces will be compared under both dry and wet process conditions. Measurements show a reduction of the resulting cutting tool temperatures of Δϑt = 27.9 % using micro-textured cutting tools compared to non-textured cutting tools. A validated simulation provides valuable information about the contact temperatures enabling a specific development of the micro-texture geometry. As a result, a reduction of the contact temperature between chip and rake face by ΔϑT = 24.7 % was possible.

No Thumbnail Available
Publication

Performance analysis of an adaptive cooling system with primary and secondary heat paths for linear direct drives in machine tools

2022 , Uhlmann, Eckart , Salein, S.

Machine tools subjected to high demands regarding productivity and accuracy are faced with the challenge that thermal losses influencing the accuracy negatively. Due to high requirements regarding thermal stability of precision related machine tool components, the focused linear direct drives (LDD) must be tempered by active cooling systems. In machine tools, a sufficient cooling capacity is available, but the cooling is insufficiently adjusted to the process and the individual demand of the heat-inducing as well as precision related components. With the intention to achieve a demand-oriented cooling, the use of thermoelectricity in machine tools is one research objective at the Institute for Machine Tools and Factory Management (IWF). Inspired by the concept of thermoelectric self-cooling (TSC)-systems for electronic devices, an Adaptive Cooling (AC)-system with thermoelectric generators (TEG) for LDD in machine tools is developed and experimentally investigated. In order to enhance the performance of AC-systems, in this research a reduction of the global thermal resistance is focused. A promising approach to achieve this goal is the division of the induced heat flow into a primary and a secondary heat path. For a model-based performance analysis of this approach, a system simulation is presented. To acquire experimental data for model validation, a test bench of the AC-system with primary as well as primary and secondary heat path is put into operation. The comparison of simulative and experimental determined data indicates a predominantly high model prediction accuracy. As a result, the implementation of a secondary heat path enables a reduction of the temperature on the upper surface of the heat source by 24.6% and thus a decrease of the global thermal resistance by 38.1%. Compared to the initial state of the AC-system only with primary heat path, the achieved thermal stability in the precision related machine tool component as well as the self-starting capability is improved.

No Thumbnail Available
Publication

Prediction of the Roughness Reduction in Centrifugal Disc Finishing of Additive Manufactured Parts Based on Discrete Element Method

2022 , Kopp, Marco , Uhlmann, Eckart

One major drawback of additive manufacturing is the poor surface quality of parts, which negatively affects mechanical and tribological properties. Therefore, a surface finishing is necessary in most cases. Due to a high material removal rate, centrifugal disc finishing is a promising mass finishing operation for an effective surface finishing of additive manufactured parts. However, due to machining the workpieces in a freely movable manner, the process is hardly controllable, and the process design is often based on time-consuming and cost-intensive trial-and-error approaches. Especially when it comes to the machining of complex-shaped workpieces, finishing results are barely predictable. Therefore, the aim of this study is to set up a numerical simulation of the centrifugal disc finishing based on the Discrete Element Method (DEM) to predict finishing results. A procedure to determine the required DEM input parameters is presented and the simulation was validated using a freely movable force sensor. The results of the finishing experiments with additive manufactured workpieces made of Ti-6Al-4V were correlated with the simulated results. The derived correlation was used to predict local differences in the roughness reduction, which occurred when finishing workpieces with a limited accessibility to the surface. As a result, it is concluded that the complex relationship between the type of media, the accessibility to the surface, and the achievable finishing results can be modeled using the DEM.

No Thumbnail Available
Publication

Revealing dynamic processes in laser powder bed fusion with in situ X-ray diffraction at PETRA III

2022 , Krohmer, E. , Schmeiser, F. , Wahlmann, B. , Rosigkeit, J. , Graf, G. , Spoerk-Erdely, P. , Clemens, H. , Staron, P. , Körner, C. , Reimers, W. , Uhlmann, Eckart

The high flux combined with the high energy of the monochromatic synchrotron radiation available at modern synchrotron facilities offers vast possibilities for fundamental research on metal processing technologies. Especially in the case of laser powder bed fusion (LPBF), an additive manufacturing technology for the manufacturing of complex-shaped metallic parts, in situ methods are necessary to understand the highly dynamic thermal, mechanical, and metallurgical processes involved in the creation of the parts. At PETRA III, Deutsches Elektronen-Synchrotron, a customized LPBF system featuring all essential functions of an industrial LPBF system, is used for in situ X-ray diffraction research. Three use cases with different experimental setups and research questions are presented to demonstrate research opportunities. First, the influence of substrate pre-heating and a complex scan pattern on the strain and internal stress progression during the manufacturing of Inconel 625 parts is investigated. Second, a study on the nickel-base superalloy CMSX-4 reveals the formation and dissolution of γ′ precipitates depending on the scan pattern in different part locations. Third, phase transitions during melting and solidification of an intermetallic γ-TiAl based alloy are examined, and the advantages of using thin platelet-shaped specimens to resolve the phase components are discussed. The presented cases give an overview of in situ X-ray diffraction experiments at PETRA III for research on the LPBF technology and provide information on specific experimental procedures.