Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters

3
Reset filters

Settings
Now showing 1 - 3 of 3
  • Publication
    Laser beam welding of additive manufactured components: Applicability of existing valuation regulations
    ( 2022)
    Jokisch, T.
    ;
    Gook, Sergej
    ;
    Marko, Angelina
    ;
    Üstündağ, Ömer
    ;
    Gumenyuk, A.
    ;
    Rethmeier, Michael
    With additive manufacturing in the powder bed, the component size is limited by the installation space. Joint welding of additively manufactured parts offers a possibility to remove this size limitation. However, due to the specific stress and microstructure state in the additively built material, it is unclear to what extent existing evaluation rules of joint welding are also suitable for welds on additive components. This is investigated using laser beam welding of additively manufactured pipe joints. The welds are evaluated by means of visual inspection, metallographic examinations as well as computed tomography. The types of defects found are comparable to conventional components. This is an indicator that existing evaluation regulations also map the possible defects occurring for weld seams on additive components.
  • Publication
    Laser Welding of SLM-Manufactured Tubes Made of IN625 and IN718
    ( 2019)
    Jokisch, Torsten
    ;
    Marko, Angelina
    ;
    Gook, Sergej
    ;
    Üstündag, Ömer
    ;
    Gumenyuk, Andrey
    ;
    Rethmeier, Michael
    The advantage of selective laser melting (SLM) is its high accuracy and geometrical flexibility. Because the maximum size of the components is limited by the process chamber, possibilities must be found to combine several parts manufactured by SLM. An application where this is necessary, is, for example, the components of gas turbines, such as burners or oil return pipes, and inserts, which can be joined by circumferential welds. However, only a few investigations to date have been carried out for the welding of components produced by SLM. The object of this paper is, therefore, to investigate the feasibility of laser beam welding for joining SLM tube connections made of nickel-based alloys. For this purpose, SLM-manufactured Inconel 625 and Inconel 718 tubes were welded with a Yb:YAG disk laser and subsequently examined for residual stresses and defects. The results showed that the welds had no significant influence on the residual stresses. A good weld quality could be achieved in the seam circumference. However, pores and pore nests were found in the final overlap area, which meant that no continuous good welding quality could be accomplished. Pore formation was presumably caused by capillary instabilities when the laser power was ramped out.
  • Publication
    Application of D-optimum experimental designs in consideration of restrictions for laser metal deposition
    ( 2017)
    Marko, Angelina
    ;
    Graf, Benjamin
    ;
    Gook, Sergej
    ;
    Rethmeier, Michael
    The process of laser metal deposition can be applied in many ways. Mostly, it is relevant to coating, for repair welding and for additive manufacturing. To increase the effectiveness and the productiveness, a good process understanding is necessary. Statistical test planning is effectual and often used for this purpose. For financial and temporal reasons, a restriction of the test space is reasonable. In this case, it is recommended to use a D-optimal experimental design which is practically applied to extend existing test plans or if process limits are known. This paper investigates the applicability of a D-optimum experimental design for the laser metal deposition. The results are compared to the current results of a full factorial test plan. Known restrictions are used for the limitation of the test space. Ti6Al4 is utilized as substrate material and powder. Comparable results of the D-optimal experimental design and of the full factorial test plan can be demonstrated. However, 80 % of time can be saved by the experimental procedure. For this reason, the application of D-optimal experimental design for laser metal deposition is recommend.