Fraunhofer-Institut für Produktionsanlagen und Konstruktionstechnik IPK

Filters
Reset filters

Settings
Now showing 1 - 10 of 113
  • Publication
    Wolframschmelzcarbidbasierte MMC-Schichten für den industriellen Einsatz im Formenbau
    ( 2022)
    Langebeck, Anika
    ;
    Jahnke, Christian
    ;
    Wünderlich, Tim
    ;
    Hein, Christoph
    ;
    Bohlen, Annika
    ;
    Uhlmann, Eckart
    Zur Steigerung der abrasiven Verschleißbeständigkeit können Oberflächen lokal mit Hartpartikeln verstärkt werden. Diese sogenannten Metal-Matrix-Composit(MMC)-Schichten können mittels Laserstrahldispergieren gefertigt und durch Mikrofräsen nachbearbeitet werden. Im hier vorgestellten Forschungsvorhaben wurde als Grundwerkstoff verwendete Aluminiumbronze (CuAl10Ni5Fe4) mit Wolframschmelzcarbid verstärkt. Der Hartpartikelgehalt kann dabei durch eine Steigerung des Pulvermassenstroms bis zur Packungsdichte des unverarbeiteten Pulvers erhöht werden. Über eine temperaturbasierte Leistungsregelung kann eine gleichbleibend homogene MMC-Schicht mit konstanter Dicke und Tiefe dispergiert werden. Durch das Mikrofräsen mit optimierten Parametern können qualitativ hochwertige MMC-Oberflächen für den industriellen Einsatz in Spritzgusswerkzeugen hergestellt werden. Dabei wurde vor allem der Zahnvorschub fz als kritischer Prozessparameter identifiziert.
  • Publication
    In situ microstructure analysis of Inconel 625 during laser powder bed fusion
    ( 2022)
    Schmeiser, Felix
    ;
    Krohmer, Erwin
    ;
    Wagner, Christian
    ;
    Schell, Norbert
    ;
    Uhlmann, Eckart
    ;
    Reimers, Walter
    Laser powder bed fusion is an additive manufacturing process that employs highly focused laser radiation for selective melting of a metal powder bed. This process entails a complex heat flow and thermal management that results in characteristic, often highly textured microstructures, which lead to mechanical anisotropy. In this study, high-energy X-ray diffraction experiments were carried out to illuminate the formation and evolution of microstructural features during LPBF. The nickel-base alloy Inconel 625 was used for in situ experiments using a custom LPBF system designed for these investigations. The diffraction patterns yielded results regarding texture, lattice defects, recrystallization, and chemical segregation. A combination of high laser power and scanning speed results in a strong preferred crystallographic orientation, while low laser power and scanning speed showed no clear texture. The observation of a constant gauge volume revealed solid-state texture changes without remelting. They were related to in situ recrystallization processes caused by the repeated laser scanning. After recrystallization, the formation and growth of segregations were deduced from an increasing diffraction peak asymmetry and confirmed by ex situ scanning transmission electron microscopy.
  • Publication
    Advances in Modeling of the Kerf Formation considering the Primary and Deflection Jets for the Abrasive Water Jet Technology
    ( 2021)
    Uhlmann, Eckart
    ;
    Kruggel-Emden, Harald
    ;
    Männel, Constantin
    ;
    Barth, Enrico
    ;
    Markauskas, Darius
    Processing of difficult to machine materials is a promising application for abrasive water jet kerf cutting and milling. However, due to the large number of interactions of an energy-bound cutting process, a precise prediction of the material removal is crucial for its application. Based on an analytical approach, a material removal simulation model is introduced considering the primary and deflecting jet impacts to rapidly predict various cutting situations. The model describes fundamental cutting mechanisms considering the water jet's material removal rate and is calibrated for titanium aluminides. The model allows for a comprehensive kerf prediction and thus potentially accelerates the process design improving the productivity and quality for abrasive water jet kerf cutting and milling.
  • Publication
    Fully coupled wet cylindrical turning simulation using the Finite-Pointset-Method
    ( 2021)
    Uhlmann, Eckart
    ;
    Barth, Enrico
    ;
    Quellhorst, Alexander
    ;
    Seifarth, Tobias
    ;
    Kuhnert, Jörg
    ;
    Nabbout, Kaissar
    ;
    Sommerfeld, Martin
    In industrial machining operations, many turning processes are carried out under wet conditions. In contrast, most simulation tools are only suitable for dry cutting processes due to challenges of modeling fluid-structure-interactions (FSI). In this paper, a wet, fully coupled cutting simulation using the Finite-Pointset-Method (FPM) is presented and validated for industrially relevant cylindrical turning. To facilitate the required reduction of the calculation effort, different routines like adaptive numerical discretization are applied. The results indicate different cutting fluid effects like evaporation areas around the chip.
  • Publication
    Ex Situ Residual Stress Analysis of Chemical Vapor Deposited Diamond Coated Cutting Tools by Synchrotron X-Ray Diffraction in Transmission Geometry
    ( 2021)
    Hinzmann, Daniel
    ;
    Böttcher, Katrin
    ;
    Reimers, Walter
    ;
    Uhlmann, Eckart
    When machining difficult-to-cut, nonferrous materials, chemical vapor deposited (CVD) diamond-coated cutting tools are applied. The tools' favorable mechanical property profile is based on the hardness of the coating as well as the adaptability of the substrate. Nevertheless, the reproducibility of machining results and process stability are limited by insufficient coating adhesion. The resulting cutting tool failure is based on coating delamination initiated by crack development. By assessing residual stress as an influence of coating adhesion, an analysis of CVD diamond-coated tools is performed using synchrotron X-ray diffraction in transmission geometry. Investigation of a nanocrystalline and multilayer morphology on cobalt-based tungsten carbide (WC-Co) and a silicon nitride-based ceramic (Si3N4) provides the distribution of the principal in-plane residual stress tensor component s22 depending on the coating morphology and substrate material. Contrary to microcrystalline CVD diamond, nanocrystalline layers decrease the compressive residual stress. In addition, the CVD diamond coating deposited on the Si3N4 substrate material tends to induce an overall initial tensile residual stress that leads to increased tool performance compared to WC-Co-based coated tools. Variation of the coating morphology as well as the substrate material offers the possibility to extend the current model for residual stress-dependent tool failure.
  • Publication
    Analysis of influencing factors for the dressing process in double side face grinding
    ( 2021)
    Uhlmann, Eckart
    ;
    Lichtschlag, Linus
    In grinding, the design of the dressing process is an essential part of work preparation and restoration of the grinding wheel's profile and cutting ability. In contrast to most grinding processes, the choice of dressing parameters in double face grinding with planetary kinematics has so far only been experience-based. As a consequence, the dressing process causes a higher degree of tool wear than the machining of the workpieces. A focused design of the dressing process based on a scientific data could help to improve the ecological and the economic efficiency by reducing tool wear and the amount of dressing tools used. In this paper, methods for determining the wear condition and the result of the dressing process, including macro- and microscopic characteristic are presented. This includes a correlation analysis between parameters of wear characteristics and workpiece surface quality. Furthermore, technological investigations are carried out in order to systematically limit the main influencing factors on the dressing process. As a result, the parameters dresser grain size dgd, rotational speed ratio nld and the machined dresser height ∆hd are identified as significant for dressing. The knowledge about their principal influence on the dressing result could provide the basis for further research.
  • Publication
    Concept for an actuated variable tool electrode for use in sinking EDM
    ( 2021)
    Uhlmann, Eckart
    ;
    Streckenbach, Jan
    ;
    Thißen, Kai
    ;
    Schulte Westhoff, Bela
    ;
    Masoud, Abd Elkarim
    ;
    Maas, Jürgen
    Typically, a large number of individual tool electrodes has to be used in sinking electrical discharge machining (sinking EDM) to successfully machine a single workpiece. Due to non-uniform wear and insufficient flushing of the working gap electrode geometries have a significant effect on the process efficiency. This paper discusses the use of an actuated variable tool electrode for sinking EDM to reduce the number of required tool electrodes and to increase the overall process efficiency. A miniaturised linear actuator was developed to individually move electrode segments to form the target shape for the tool electrode. The coordinated actuation of bundled electrode segments introduces new methods for the active flushing within the working gap, which cannot be implemented in conventional sinking EDM. Intelligent sinking strategies can further improve process efficiency by creating and sinking sub-geometries into the workpiece offering improved flushing conditions compa red to the original geometry.
  • Publication
    Effects on part density for a highly productive manufacturing of WC-Co via laser powder bed fusion
    ( 2021)
    Polte, Julian
    ;
    Neuwald, Tobias
    ;
    Gordei, Anzhelika
    ;
    Kersting, Robert
    ;
    Uhlmann, Eckart
    The additive manufacturing of parts made from difficult-to-weld materials through the usage of preheating temperatures of up to Î0 ⤠500 °C is enabled by newest L-PBF machine tools, such as the RenAM 500Q HT from the company RENISHAW PLC, Wottun-under-Edge, UK. This work aims to delevop processing parameters for the dense and crack-free manufacturing of tungsten-carbide cobalt (WC-Co) via this off-the-shelf machine tool. Therefore the laserpower and scanning speed were varied between 80 W ⤠PL ⤠350 W and 140 mm/s ⤠vS ⤠650 mm/s respectively. Furthermore the influence of a continuous and pulsed laser mode was analysed. A focus was set on the identification of parameters that enable a highly productive manufacturing while maintaining a high part density. A parameter set for relative density rel. > 94 % and a buildup rate v = 0.59 mm3/s was developed.
  • Publication
    Data for a simulation of metal cutting with cutting fluid using the Finite-Pointset-Method
    ( 2021)
    Uhlmann, Eckart
    ;
    Barth, Enrico
    ;
    Seifarth, Tobias
    ;
    Höchel, Maximilian
    ;
    Kuhnert, Jörg
    ;
    Eisenträger, Almut
    The measurement and simulation data, their preparation and the simulation setup published in this co-submission are related to the article ""Simulation of metal cutting with cutting fluid using the Finite-Pointset-Method"". Wet and dry turning experiments were conducted at the Institute for Machine Tools and Factory Management(IWF), Berlin, Germany. Required adaptions of the used software MESHFREE were performed at Fraunhofer ITWM, Kaiserslautern, Germany. Both institutes collaboratively developed and validated the orthogonal cutting simulation model using the Finite-Pointset-Method (FPM). In this paper all measurement and simulation data and their preparation methods are presented in detail. This includes the preparation methods of process forces, analysis of chip morphology images as well as measured contact lengths on tool rake faces. Moreover, the experimental and simulation data are provided at the Mendeley Data repository. Hence the reader can use the data for own validations and analysis. Furthermore, the used simulation model files are completely published at the Mendeley Data repository. It allows the reader to retrace all settings. In addition, this enables to repeat the simulations and to simulate other process parameter combinations according to own interests.
  • Publication
    Evaluation of carbon fiber reinforced polymer – CFRP – machining by applying industrial robots
    ( 2021)
    Grisol De Melo, Ever
    ;
    Santos Silva, Jéssica Christina dos
    ;
    Klein, Tiago Borsoi
    ;
    Polte, Julian
    ;
    Uhlmann, Eckart
    ;
    Oliveira Gomes, Jefferson de
    Carbon fiber reinforced polymer (CFRP) is widely used in high-tech industries because of its interesting characteristics and properties. This material presents good strength and stiffness, relatively low density, high damping ability, good dimensional stability, and good corrosion resistance. However, the machinability of composite materials is complex because of the matrix/fiber interface, being a challenging machining material. The CFRP milling process is still necessary to meet dimensional tolerances, the manufacture of difficult-to-mold features like pockets or complexes advance surfaces, finish the edges of laminated composites, or drill holes for the assembly of the components. Besides, the demand for low-cost, reconfigurable manufacturing systems of the industry demonstrates that the application of industrial robots (IRs) in the CFRP milling process becomes an alternative for providing automation and flexibility. Therefore, the objective of this work is to evaluate the performance of the low payload IR KUKA KR60 HA in a milling experiment of CFRP, which indicates its potential application as an alternative to milling process. Furthermore, the influence of the cutting tool geometry as well as the cutting parameters in the machining behavior with IRs is evaluated.